Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello support team,
I am developing a mobile app to communicate on BLE coded phy (long range) with nrf5340DK. The nrf connect for mobile on android works fine, but not ios...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
Hello,
I am going through the intermediate DevAcademy tutorials right now because I specifically need to use the 52840 dev kit to interface with a SPI driven ili9340 device...
Hi everyone,
Edit: Consider that I'm on ncs 2.6.1
What are the current methods for provisioning an nRF9160 on the nRF Cloud? I have an ongoing project with the nRF9160...
This sample can be found under samples/nrf_compress/mcuboot_update in the nRF Connect SDK folder structure.I want to know the whole decompression process,I added a lot of...
Hi,
I am building an app that connects to the NRF52840 with BLE. The NRF board is attached to an electrocardiogram(ECG) setup, so I am interested in the app being able to...
Hello,
I am using the hci_usb sample from Zephyr and running BlueZ 5.53 on Ubuntu 20.04. I am trying to increase the ACL packet size from the default value of 27 bytes and...
Hi,
I am using SDK v2.6.1.
Is there any course available on DevAcademy for WebSockets?
For WebSocket i take reference of v2.6.1/zephyr/samples/net/sockets/websocket_client...
Hello there,
I am using nrf connect sdk using vs code.
Toolchain: v2.7.0 SDK: v2.7.0
I have custom hardware board based on nrf52811 SoC.
I have completed a firmware...
Hi
We have a project previously built on NCS v2.6.0 and now we need to migrate it to v2.8.0
I see from v2.9.0 child/parent build setup is not supported and so we are planning...
I'm using ”ncs\v2.8.0\nrf\samples\nrf_compress\mcuboot_update“ this routine.After connecting the Bluetooth, put in the DFU package (mcuboot_update\build\dfu_application.zip...
Hi,
We are trying to enable oversampling in an application that is based on your DF connectionless RX sample, build with Zephyr version 3.4.99.
Something similar was asked...
Hi,
I've a good experience with nRF5340 pre-certified modules and nRF Connect SDK. I'm evaluating leveraging Nordic Thingy:91 X platform to build a new product. However...
Hi Team,
I have some questions following,
1. We created custom board by using nrf52833. for custom board any bootloader needed?
2. We are able to flash hex file into...
Hi i am currently, doing development on nrf52840. where I have 48 number of GPIO's available. for my application, I have peripherals like Touch screen RGB display, UART based...
