Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi, I'm using nrf52810 ,nrf connect, zephyr, vscode extension. I’m having trouble using both UART0 and the NUS UART service. Here’s a snippet from my overlay file:
/ ...
Hello everyone, I'm trying to perform a device firmware update using the buttonless service on nRF52DK with SDK v17.1.0 and Softdevice S132.
I can connect correctly to my...
Hi,
I’m working with Timer 0 on my nRF5340 DK and trying to set up two different intervals: one at 1 second and another at 60 seconds, each on separate channels (COMPARE0...
If I am to do a custom SPI Slave driver to achieve ultra low latency handling and would like it to coexist with NCS / Zephyr, is there a document describing this ?
E.g....
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it is iBASIS...
Dear ESB technical specialist
Regarding the ESB function of nRf52833.
The datasheet explains BLE function, but there is no explanation about ESB.
For this reason,...
Hello,
We are using the nRF52832 in our product, along with nRF Connect version 2.6.0.
We have been working on obtaining Bluetooth certification, but we encountered issues...
As I understand it, the nrf samplesaws_iot and aws_iot_mqtt assume there a network connection up and running.
I am trying to adapt the sample to create the connection via...
Hello,
The target MCU on nRF5340 DK seems to use internal load caps for the high frequency 32MHz XTAL because the board does not have external load caps.
The nRF5340 specification...
Hi,
While I understand that the sample code is not intended for the nRF52 Dongle, I am still wondering if I can make it work on it.
I have successfully tested it on...
Subject: Request for Assistance: Coding BLE and SPI for Gesture Control using nRF52840
Dear nRF Support Team,
I hope this email finds you well. My name is sharon and I...
Is there any analog to digital input on the nRF9061 SiP / DK? I essentially need to plug in a microphone to this, so I looked at a couple of options -- ADC, the DMIC interface...
Hi,
I'm using an nRF9160DK v1.0.1 (2021.26) for developing an application on the nRF9160 with ncs v2.5.0 and I'm currently looking to optimize current consumption. I realize...
In my project, my master controller need to scan devices through custom uuid.
One problem is that in ble_advertising_init, I can only add 16bits uuid and type of which is...
