I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello Experts,
I am writing a code for nRF52833 using the SDK nRF5 version v16 using the Segger Embedded Studio as development environment.
In my code when sd_ble_gap_adv_start...
Hi,
We are using nrf connect SDK in VS code environment (V2.70) on Windows. The toolchain (C:\ncs\toolchains\ce3b5ff664) contains cmake v3.21. For our project, we require...
Hello, I want to purchase cables to connect a Flasher Pro (cable should end on DB20 Female) to an nRF52-DK onto "Debug In" connector (cable should end on mini DB10 Female...
Hello, I am developing a solution based on nrf52-DK, using nRF52832.
I am trying to use JFlash to read Device Serial Number. I could read it with JLink , with command "mem32...
Hi, hope someone can help me.
The past 3-4 years I have used SDK 17.1.0 and SES for SW development where the SW is running on a nRF52840 SoC which is the heart of our product...
I'm working on a Docker image that includes a VS Code server for the purposes of workshops and training, and I'd like to install the nRF extensions (e.g. https://marketplace...
hi，bro
I want to support both BLE and GZLL simultaneously and perform the corresponding initialization work based on the value of a variable, mode . However, when I set...
Hi,
I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone.
I can capture all the pairing process, I see DHKey exchange...
Greetings!
I am looking into Bluetooth Mesh, and the allowed radiated power according to Norwegian law. The general limit for 2.4GHz is 10mW, but if we utilize FHSS the...
Hello, I'm running into an issue with the "modem shell for NR+" application on a pair of nrf9131ek evaluation kits. The local sales rep. suggested that I reach out to Nordic...
Hello, I have a pair of nRF9142EK devices that I've been using to test DECT NR+. Now, I'd like to test out one of the boards with the cellular modem firmware for nRF9131EK...
Hi Support team,
I am using nRF9160 module and i want run two server on the module, one is modbus server and other is CoAP server. so is it possible to run both server...
When using the adafruit feather nrf52840 , the lowest I can seem to get power usage is around 400uA (including with the boards/nordic/poweroff sample ) .
This is my device...
