Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I want to weld my product that contains NRF52840, using an ultrasonic welding machine.
Currently I'm thinking of a welding frequency of 20KHz or 40KHz.
1. Is there...
I am currently working on a NINA-B4-TAG from ublox, there is a requirement to be able to dynamically turn on and off the CTE without completely turning the advertising off...
I am thinking of using nRF5340 Audio on a development board.
The I2S-compatible IC on the headset side is an IC called AK4432VT.
The following settings are required to...
Hi,
We have a nrf5340 module on a custom PCB that is connected to a computer through use of a pcie header. This PCIE header allows USB communication to the module and supplies...
Hi,
In my project I need to send maximum bytes possible inside one package. When using the nrf connect app I can see that when reading the characteristic this works, but...
Hi . I have two questions about the PIPEs in Zephyr RTOS , especially regarding the correct use of the k _pipe _put and k _pipe _get functions :
1 ) In both functions ,...
Hi,
when I configure CONFIG_BT_SETTINGS=y as I want the device to remember the pairing parameters, the services defined with BT_GATT_SERVICE_DEFINE dissapear.
As far as...
Hi,
I use nrf52833 running ncsv2.6.0,
I trans v2.6.0\nrf\samples\bluetooth\central_hids to \ncs_v2.6.0\v2.6.0\zephyr\samples\subsys\usb\hid and now plus usb to nrfUSB...
How do I switch nrf52832 from a broadcaster to a peripheral with a service via a keystroke interrupt? After trying it out, I found that my problem was mainly: I didn't know...
Hi,
I'm trying to control nrf9160 SIP from stm32 MCU via AT Commands. Should I program on the nrf9160 the AT_CLIENT sample for this purpose or is not neccesary?
I'm trying...
Hello Team, We are currently working on a project for interfacing Larger TFT LCD display with Capacitive touch with nRF5340 Devkit board and SoC. As per the datasheet of the...
We use custom board with NRF52840 and a MODBUS CO2 sensor. We are struggling with power consumption when the serial is enabled. The goal is to take measurements and then put...
// <i> NRF_FSTORAGE_SD uses the nrf_fstorage_sd backend implementation using the SoftDevice API. Use this if you have a SoftDevice present. // <i> NRF_FSTORAGE_NVMC uses the...
Hi to all,
I have a problem and a question regarding the power measurement setup I’m working on.
Regarding the problem, I am trying to measure the power consumption...
