Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
To use the nRF54L15 SPI00 and SDHC, I have to edit the SDHC file and add board-specific configurations to start at a 1 MHz clock, since the SDHC file defaults to a lower frequency...
Hello,
I was going through "Bluetooth Low Energy Fundamentals" https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/ .
I feel few need to be corrected...
Does Nordic make available 3d models (.stp files) for the nrf7002, nrf5340, and/or npm1300 chip scale parts?
The only information I can find on this is in a forum post...
Problem After successfully establishing a nRF7002EK WiFi connection to the local network, AWS IOT connection fails with “mqtt_helper: mqtt_connect, error: -2” and reboots...
Problem When attempting to flash a nRF board that uses pyocd as the runner (defined in devices’s baord.cmake) for flashing, the following error occurs.
It doesn’t matter...
Hi Nordic team,
I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively.
I am using NCS 3.3...
I'm developing a custom BLE sensor on an nRF52832 (E73-2G4M04S1B module, SoftDevice S132 7.2.0) with a companion Android app. On Xiaomi/HyperOS devices (confirmed on this...
Just purchased the PPK 2 Did the quickstart up and got this a message saying it's not yet supported. I am running Ubuntu Linux :
Distributor ID: Ubuntu Description: Ubuntu...
Your application for SUPL-C license has been denied.
Please make sure you have an active/approved DevZone account
You must apply using the same email address as for...
Hello,
I am using nrf5340 audio sample with the custom board. The nRF Connect SDK version I used is v3.4.0.
I added the following settings to prj.conf so that the custom...
Hi all,
the nRF54L15 hardware can support an external RF antenna switch. I don't see any hardware limitations (the switch could be controlled via GPIO), but the more interesting...
We are using the nRF9160 with firmware 1.3.6 to establish a DTLS connection to a server, using the Zephyr TLS stack.
The following problem occurs quite frequently: After...
Hi Nordic Team,
I would like to report a bug I hit while testing my project.
Project configuration:
Use fota_download with CoAP protocol to download new images (coap...
Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
