Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi,
NCS2.0.2, nRF5340 audio DK, VScode
about Le Audio
1.CIS mode,when is bidirectional communication supported?
2.when LC3 support 16bit 16kHZ?
3.when suppourt DFU...
Hi i wonder how could i program the nRF Dongle with the sample thread_cli in order to being able to use the thread topology monitor?
I know that i have to use the Programmer...
I connected my NRF52840 DK board via USB to my Macbook Air. In VS Code, under "Connected Devices" I was expecting it to show up as "NRF52[...]" but it is showing up as "NRF51xxx_xxAA_REV1...
Hi,
follow the to do DFU over UART on nRF5340, it fail in the last step "image confirm".
The console show
What is the meaning "Error: 3"? How to fix it?
Can I...
We have relatively big model composition, and reading it via nRF Mesh app fails if it exceeds 21 segment message.
However the limit I assume should be at 32 segments and...
Hi,
We have done a lot of projects with nrf52832 with softdevice S332 v5 before.
Now we have a new project to use nrf52840. Can we use the original s332 version? Or do...
I and looking at using an nRF52 device with the nRF Connect SDK version 2.x with a Zephyr Bluetooth LE Controller in a peripheral application where the advertisement data...
Hello,
I am running windows 10 and started the DevAcademy lesson 1, exercise 1 and exercise 2.
Up to exercise 2 item 4 (add a build configuration) everything went fine...
Hello i am using an nrf52840 s140 and i am trying to write a specific event when takes place to the usb port. I am using the usbd_uart example.
It works fine for the first...
I used Nrf9160 to develop a product. Until yesterday, I had been able to connect to the nb network normally. But today, I found that my device could no longer register to...
Hi, I'm looking for help installing the nRF Connect for Desktop 3.12.0.
I've managed to unpack the application EXE and have picked out all the required pre-reqs to do the...
Hi,
I have a problem, When I first initialize Bluetooth and then initialize FDS for writing, it will fail. However, if I first initialize FDS and write data ,it is OK, then...
Hi,
We develop a custom gateway in which we use iMx6ULL and NRF52840. Both are connected over full UART.
We use this NRF52840 as a BLE HCI controller by flashing the HCI_UART...
