Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hello,
I have a strange problem and after having searched in this forum and tried to realize proposals which were given at other tickets here I need support for solving...
Good morning,
I have nRF52840 Dongle.
I am looking for a tool that will allow me to connect to a BLE device based on its name.
Need:
- find the device,
- connect...
What I'm working on:
I'm working on a small project using this nrf52840 module:
www.minew.com/.../
Access to source:
If it helps to understand my issue, all the design...
In the function "bt_scan_filter_status_get(bt_filter_status *status)" [file: subsys/bluetooth/scan.c #1302], the variable
"status->manufacturer_data.enabled" is not updated...
hi devzone
I've trouble starting nRF Connect for Desktop v3.12.0.
I'm using nrf52-dk / pca10040 board and nrf5_sdk_17.1.
when I run the program "nRF Connect for...
Hi,
I do have a question about PCB layers. I did read it is better to use a minimum of 2 layer PCB, but why is this? By example is a single layer also OK?
I'm trying to...
Hi Team,
We are using Nordic connect SDK nCS 1.9.1 & nrf52833
currently have not changed any clock frequency they're at default settings, we want to know what is the...
Hi, quick question.
Software: SDK 17.1.0 with segger embedded studio
Hardware: nrf52833-dk
Background: I read that it is possible to take iq samples of the payload....
Trying to using IEEE-802.15.4 on nRF52820 with SDK-17.1.0, Librarie 802_15_4/raw/802_15_4_lib_gcc.a.
nRF52820 n ot support FPU so set -mfloat-abi=soft in Makefile
Encounter...
I successfully completed all exercises from DevAcademy using nRF Connect SDK v2.0.0 and nRF Connect SDK v2.1.1.
However, when I tried to experiment with DevAcademy Lesson...
I have not done anything with the SDK for a while so I updated Segger Embedded Studio to the latest: 6.40 and the latest nRF SDK 17.1.0 and built my project and I only needed...
Hello together, I'm searching for a way to go I max low power mode possible an then wake a from one of three reasons:
Timer/Clock
NFC-Field
GPIO
I searched the...
I have an application setup to use RTT for console and logging whereas UART is disabled. If I enable the UART async API then RTT stops working.
Working:
CONFIG_ESB...
Hello,
I tried to run the llpm (low latency packet mode) code by establishing a connection between nrf5340dk and nrf52840 devices.
I receive a transmission latemcy between...
I've been trying to get breakpoints working on a new nRF Connect project but have been running into an issue: when I hit "Debug" in the nRF Connect plugin in VSCode, the app...
