Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
SAADC feature request: RESULT.PTR auto increment Right now, continuous sampling works well for a high sampling rate (up to about 200ksps), keeping DMA etc active to cope with...
Hi,
Im using the nRF52840 DK and im trying to set the Service and characteristics with this tutorial : https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial...
I have one light sensor model publishing light lux level of the room to Group A . On other hand, have occupancy sensor publishing to the same group A .
and one light with...
Dear All, I am working on an application where I am connecting to the network, sending some data and then disconnect using CFUN=4, in order to achieve low power for my application...
Hey Nordic's technical team,
I'm trying to write and read via I2C to a component with two bytes registers. I tried the following method:
Then switched to this one: ...
Hello,
Using v1.9.1 nrfConnect and the Coordinator example on a nrf52840 -DK. From Nordic docs: I think I may be miss interpreting Zigbee Cluster spec... Below is example...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
I want to set the GPIO of NRF52840 to the high resistance state. How do I set the GPIO of NRF52840 to the high resistance state, please help me,thanks!
Hi！
I'm working on direction finding using nrf connect sdk.
I have already make a tx (nrf52833) and a rx (nrf52833) and i succeed to receive the CTE and the IQ sampling...
I am working on adapting a project that compiles/flashes the code with a makefile that uses nrfjprog in a cmd line to program a blank nrf52480 with the softdevice and application...
Hi all
In nRF52840_PS Pin assignments sheet, some pins Recommended usage is " Standard drive, low frequency I/O only ", does that mean only low frequency (up to 10kHz...
Hi,
I am writing an application that reads data from the I2S interface, adds it to a queue and sends it via BLE (the code I have implemented so far is added at the end of...
Hello,
I am using the 802_15_4 MAC api to configure my device as a coordinator.
After it has been configured as a coordinator I want another device to connect to it...
I am using nRF52805(SDK 17.0.1 & S112) in my application development. Designed GATT Table Having some custom services with read, write & notify properties, And also, there...
