I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
I am trying to set the Tx power level on the central device, I have followed the nordic example samples/bluetooth/hci_pwr_ctrl in the Zephyr tree. But it only sets for...
I am using ncs2.9.1.
I am currently testing Bluetooth mesh dfu using 54l15dk. Now I want to put the firmware that is ready for updating into the external flash of the distributor...
I used the NUS example and enabled the Bluetooth DFU function. By default, the first and second firmware slots are both placed in the internal flash. At this time, the Bluetooth...
Hello, I am trying to convert my codebase from segger embedded studio to nrf connect. I am currently working on the spi section of my codebase.
I am communicating from...
1st problem:
There are some failed case when i run \v2.9.1\modules\bsim_hw_models\nrf_hw_models\tests\zephyr_apps\54_aar_ccm_ecb\src\test_ccm.c
2nd problem:
If I...
After I updated to v2024.11.22 of the nRF Connect For VS Code I can no longer get the option: "nrf-connect.debugging.flash": false to work. It keeps flashing the device before...
I use NRF54L15 DK to develop channel sounding feature on zephyr SDK or nRF connect SDK.
How to configure CSTONES related registers to transmit and receive CS Tone packets...
Hello,
I’m working with a custom board using the nRF54L15 and the latest Nordic SDK, and I’m facing an issue while trying to communicate with an nPM1300 over I2C.
Here...
Hi all,
I'm working on a project with an nRF52840 using the nRF Connect SDK (version X.Y.Z) and Zephyr RTOS. My goal is to achieve maximum possible range for non-connectable...
nrf modem: 1.3.4
sdk: 2.3.0
Custom board.
We have an asset tracker that caches events when out of connectivity zone. We can accumulate 10-100 messages depending upon...
Hello!
I have designed a custom board with the nRF5340 , powered at 1.8V. I am able to program the chip successfully, but after the firmware is downloaded (Zephyr RTOS,...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
Hi,
We want to enable zephyr shell over RTT on our custom board based on nrf52840. I tried the 'shell_module' sample with prj_minimal_rtt.conf and it works fine on nrf52840...
Hi there,
I built a battery powered custom PCBA with the NRF54L15 and the nPM1300. All the configuration and register work via I2C seems to be working properly (reading...
Hi. I have a working IAR project based on the nrf52 SDK \nordic\examples\ble_peripheral\ble_app_uart. i am attempting to port the project to ARMGCC using VSCode. I am at a...
