Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
To the kind attention of Nordic team,
About what has been said in https://devzone.nordicsemi.com/f/nordic-q-a/51879/saadc-in-sample-convert , I'd like to know if the blocking...
Dear Member,
I want to call nrf_libuarte_async_rx_free from another file outside main.c
nrf_libuarte_async_rx_free(&libuarte1, (uint8_t *)&GPS.rxTmp, 1);
I got
.....
I was following the article here on programming the nRF52840 Dongle, but am running into issues, and I have other questions as well.
(+) nRF52840 Dongle Programming Tutorial...
2021-02-01 EDBOND Hi Nordic and fellow nrf users
In my project the host cpu is SPI master, Thusthe nrf52 needs to spis slave. Using 2 DK-52 Boards, - nRF5_SDK_17.0.2_d674dde...
Hi,
I am doing some research for the antenna matching of the NRF52832. Now the product specification v1.4 on page 551 states:
"A matching network is needed between the...
How to make the nRF52840 SPI work in 8M with 1.8V supply?
We test the PCA10056 nRF52840 DK board, and find the 8M SPI CLK&DATA wave is very bad. The 8M SPI works fail with...
hi
I tried zigbee tx carrier mode start at 11 channel and tx power = NRF_RADIO_TXPOWER_POS8DBM.
But, When measured with measuring equipment, i got zb tx power -20 ~...
I recived nrf5 SDK V17.0.2
I'm testing with in "nRF5_SDK_17.0.2_d674dde\examples\peripheral\radio_test" folder.
I tried zigbee tx carrier mode start at 11 channel and...
The application I am designing gets a pulse ox measurement from the user, sends it, disconnects, and shuts off. Are there any deleterious side effects of exiting the main...
Is it possible to fill some field when sending advertise message.
We want to change some filed periodicity, so is it possible every time sending the advertise message. ...
Hi,
I still have issue with programming.
I don't understand why i always have trouble with DLL.
I'm able to program with SES, the bootloader and my application. But...
I have a BMD-300 Eval board with the nRF52832 programmed as SPI slave using the SPIS example program. It works, but I cannot figure out how to send a message back to the master...
Hi,
I have done some reverse eng on a nrf24l01+ emitters using spi spy and managed to catch datas using an arduino leonardo + nrf24l01+ using the following register setup...
Hi All,
I have an nrf52833DK and now I want to debug the program.
I am using NCS V1.4.99 and using SES for development. I created a 52833 project, but I used the nrf...
