Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello
I'm using nrf52832 and sdk v17.0 and I'm testing in the example of ble_app_uart.
I'm creating a feature that Bluetooth disconnecting and then stops advertising....
When working with AT#XHTTPCREQ we have encountered the following provlems:
1. Sending AT Command `AT#XHTTPCREQ="POST","/upload","Content-Length:3357",3357` with the payload...
HI!
I'm currently working on a project where I'd like to send and receive BLE messages using my own channel hopping mechanism.
I've read into the 17.0.2 Examples ...
I am having trouble connecting to an nRF52810 in a uBlox BMD-330 Eval Kit.
It has previously been successfully flashed with custom firmware but, now, when I try to connect...
The specifications for Flash programming in section 4.3.7.1 page 21 is blank in the nRF52810 Product specification 1.0. Can you please provide the values for this table?
Hi all,
I am not able to update the modem firmware over usb/mcboot with the programmer on my Thingy91. I have tried both on linux and win 10, the problem is the same. The...
Hi,
I have been using the NUS on nRF52832 DVK with no issues, however, when I migrated to the nRF52840 DVK and a custom board based on the 52840, the NUS characteristics...
Hello Nordic Community,
I am currently following the SMP guide provided here: https://docs.zephyrproject.org/latest/samples/subsys/mgmt/mcumgr/smp_svr/README.html
The...
Hey,
I am wondering if it is possible to run MTD and SED on the CoAP server on nRF Connect SDK v1.4.0.
I have looked at the question " How do I set up CoAP Server whit...
Hello,
We are going to design our new product using NRF52832. Please suggest if there is any other better IC which has higher transmission range, higher RAM and with less...
there is a module in the skylab project on the nRF52832 chip and it does not agree with the tablet, which is old BT. Is it possible, through the firmware or SDK, to downgrade...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
