Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I am reading the PPI Example at the Infocenter as shown by the link below: -
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Fppi_example...
Hello Nordic,
I worked with the interactive PyACI during several months by using my PC (running the interactive PyACI) connected through usb to a DK used as provisioner...
Hello,
We've recently migrated from SDK version 15.2.0 to 17.0.0 and noticed an anomaly with the clock driver. If the watchdog is started, then after any soft reset (through...
Hello! How can I measure the heap size (total and free space) at runtime?
Right now I'm working with some legacy code that makes a call to mallinfo()
That call returns...
I am testing "nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\experimental\ble_app_cli" example.
Do I need 2 boards to run this example ???
What I got from the infocenter...
Hi
I am using SDK17. I am running the app_pwm example and i get an error with the "nrf_drv_state_t", it is not defined and the "NRF_DRV_STATE_POWERED_ON" is not defined...
Hello,
I'm programming nrf52 with SDK17. My application requires to advertise in 1 channel and also scan in 1 channel too. I have done the code. But when I run the code...
Hi,
I'm programming nRF52833 for my application. I have done to configure my device and it advertised and scanned sequentially. For my application, I advertise and also...
Hi:
I am trying the "Mesh Serial" example on my nrf52840 boards. However, when the Echo command is used after the device is cold-started , a timeout event will occur. I...
hai ,
i am using nrf52840 sdk 15.2 and in my application i have to connect nrf52840 central to peripheral after connection i have write data on ble_lbs_led_status_send i...
Hi,
I am using NR52832 with nRF5_SDK_15.3.0_59ac345 .
I want to scan nearby mobile BLE devices and get its data from its advertising data and also its scan response data...
Hi,
Hi, we have a latency-critical use-case and found the Low Latency Packet Mode ( LLPM ) as a possible solution.
Our current application is using nRF5 SDK 16.0 with...
Hello Devzone
Currently I am following below link to setup the “HID configurator for nRF Desktop”.
link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
Hello, guys!
We are in an evaluation phase of our future product. Our plan is to use nRF52840-based module and the latest SDK 17.0.2 or FreeRTOS or Zephyr RTOS (will be...
