When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
The questions are related to nrf9160:
How much memory space is currently used and free on the Thingy:91, nrf9160?
How much memory would take a complex timing routine...
I'm working nrf52832 , SDK V15.3.0 and S132. I have implemented whitelist in application and its working fine. I need to add one phone as master device so i need to hard coded...
Hello,
I'm using nRF52811 SoC with nRF5_SDK16.0.0 and SoftDevice v7.0.1. I'm using following code to write data into flash. This code is tested with nRF52840 in both debug...
i want to interface the adxl345 accelerometer with the nrf52840 board
i got an code from ADXL375_12C.zip
https://devzone.nordicsemi.com/cfs-file/__key/communityserver...
Hello All,
Is there an explanation why the Pin Configuration Registers are not available for viewing in the Registers view of Segger Embedded Studio?
If there is can someone...
Hello,
We have an nrf9160 dk-pca10090 board.
We want to know if there is a way to make the two processors (nrf52840 and nrf9160) communicate using uart.
Kindly...
Hi everyone
I have a question about zigbee. After reviewing the documentation, I realized that on the nrf52840 chip, you can use zigbee with a frequency of 2.4 GHz. But...
Hi, First of all, appriciate all your hard work on tech supporting, this is my first ask in this forum. I m currently using developing nrf52832 on Zephyr , working on the...
I'm trying to integrate mesh 4.0.0 into an existing project that uses sdk 16.0.0. I'm very close, but I'm getting an error when I try to run mesh_stack_start()
I traced...
HI everyone,
I am currently facing an issue when using nrfjprog to flash my nrf52832-based custom board using nrfjprog.
Here is the steps I followed:
- Creating application...
Hi,
I have recently been evaluating the nRF52840 for the research purpose. I came across a question related to this product that I could not figure it out myself.
I noticed...
Hi Nordic
Is there any sniffer can sniffing ANT traffic?
I just trying 52840DK and nrf-sniffer-3.0, and read user guide, it seems to sniffer BLE packets only.
Regards...
Hello Supports,
I downloaded the SUPL package, and extracted it to nrf/ext/lib/bin/supl/.
For enable it in gps example, I set CONFIG_SUPL_CLIENT_LIB to y in prj.conf...
I have borrowed a snippet from github nordic repository for doing a single Vdd voltage sampling. I lifted the code and installed it directly into my app. It appears to hang...
address = 0xe7 0xe7 0xe7(3bytes),
dataLength=0x01(8bit),
S1>>PID=0x01(2bit);NO_ACK=0x00(1bit);
How to calculate CRC, I need software calculation, not hardware processing...
