Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
We are working on the GPS sample code found in the ncs\nrf\samples\nrf9160\gps folder of the nRF Connect SDK 1.1.0 tag in the repository.
The modem firmware version we...
If a record in a file with MESH_CONFIG_STRATEGY_ON_POWER_DOWN have been changed the NRF_MESH_EVT_CONFIG_STABLE is never emitted until mesh_config_power_down() is called. ...
Hi
I am working with nrf52832 development kit. I am trying to write device information service from central device to peripheral device.
I am successfully able to write...
Hello Devzone,
I've been using nRF52810, SoftDevice 112 (5.1.1), for a Mic recording application. What I'm trying to do is sample PDM MEMS mic data through PDM interface...
Dear Team,
I have nRF52 DK and nRF52840 DK, Can we program nRF9160 using nRF52 DK?
Please let me know the process and detailed wiring to program nRF9160.
Ashiq Moha...
Hi,
Good Day!
Statement of Problem: We use Li-Ion Battery in our application and would like to monitor a few variables such as Battery Voltage, Battery temperature & Discharge...
Hello, I'm trying to set up SPI communication with a sensor from my nrf5284_pca10056 running zephyr.
This is my prj.conf file:
This is my .overlay file:
And this...
I'm looking at the GPIO functions in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/peripherals/gpio.html , and looking at the function prototype...
Hi
I'm have and NRF52840 with a MPU9250 connected via TWI. The connection to the MPU9250 is successful, I can find its address on the bus (0x68).
I've implemented a very...
I am trying to add to an existing project gpiote
I have copied the code from the example project and tried to add all the files and changes to my sdk_config.h to match the...
Hello all,
I'm trying to develop a basic bike computer, compatible with ANT+. For that, I'm using nRF52 DK. My main objective is to be able to connect to any commercial...
Hello,
I have nRF52840 with code that is based on SDK16.
I am not using Softdevice in my project - just MBR , Bootloader and Application.
I was able to upgrade my code...
Hi all,
We are successfully using the nRF52840 chip in one of our projects except for the DFU functionality. We tried following these tutorials without success:
devzone...
Hi, I'm dealing with the ble long_range_demo. Central packet gives arrival time and rssi signal through the rtt viewer. However, I am willing to know the sending time of the...
