here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I use SDK12.2.0. The mobile phone has connected my 51822 device,and then the mobile phone keep away from my 51822 device till to disconnect.how to do that they will connect...
Hi Guys,
I facing issue on one of my project, our HW require 2 set of TWI and one QSPI/SPI. I notice SPI0/1 cannot be used because I need both TWI0 and TWI1 to be supported...
Hi,
I'm trying to adopt my nRF52832 projects to the nRF5 SDK version 15.2.0 and the NRFX drivers framework. I'm using a short app_config.h with NRFX_RTC_ENABLED and NRFX_RTC0_ENABLED...
Hello,
There is a example for the nrf52840 for thread with mqttsn. Although this is just for my personal use I would love to use some kind of encryption for it.
So the...
Hello. I have been trying to work with extended advertising between two nRF52840 boards using the SDK, but have had trouble in setting a long advertisement payload (as in...
I followed Einar's nRF52840 Dongle Programming Tutorial and tried the ble_peripheral/ble_app_eddystone example using SES 4.12. Opened the project, changed the preprocessor...
Hello All,
I have been using this NRF52 DK board with KEIL for like 2 weeks. I read the all the document regarding BLE 5 protocol and followed the DIY codes step by step...
Hi Sir,
In this project, we design with nRF51822-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028). The file...
Hi Sigurd,
Thank you for your reply. I have executed the code given by you (below link) in Segger studio(V 3.50) I observed that the output or load (pin 31) which is connected...
We have the device, where 2 power supplys can be applied. One of them is external regulator with 3.3 V output. We used it for additional load in our device. Another one is...
Hi,
I referred uart example in nRF SDK 15.0.0 and tried to implement on proxy_client program by adding all files which there in example. but still i'm facing compilation...
Hello!
I'm facing some problems when I try to broadcast a message from my receptor to the transmitters, I'm using 3 nRF24L01P. I read some things about setting the same...
I have 2 PCA10056 preview development boards.
The newer one (0.11.0 2018.3) works as expected.
The older board (v0.9.0 2016.48) the built-in LED1 thru LED4 do not...
I want to use application board and connectivity board with mesh sdk in nordic chip. Is there serialization is available for mesh like using in nRF SDK15.0.0 peripheral driver...
