I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
this issue might also be one of others than myself
my main development environment is based on linux ... firmware, QT, android and whatever comes along ... i used to write...
Is there native support for hardware coex lines? If we have a WiFi chip that produces a TX Active signal, can we hold transmit from the nRF52840 till that transmit is finished...
I have bought a Tayio Yuden EYSGJNZWY Bluetooth module, which is in fact just a Nordic's nRF51822 (256KB Flash and 32KB RAM) with added antenna. Tayio's files say that the...
Hi,
I have built an application which is based on BLE and protocol that supports high frequency sampling of sent messages. I tried to achive that using only BLE, but it...
Hello,
I am designing a custom board with NRF52832 IC. I have a query regarding routing of traces.
In my design, I am not using all pins of IC. Do I need to route traces...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
I'm using SDK13.0.0 ble_app_ancs_c example.
On connected with a phone, pm_evt_handler is called with PM_EVT_CONN_SEC_SUCCEEDED, and call ble_db_discovery_start(), then...
hi,
i want to make BLE central node with Nrf52840 for receiving multiple data from Nordic thingy 52,i am using keil IDE with Nordic sdk 14.2.0 and blinkey central(s140_PCA10056...
Is this possible to change MTU Size in nrf51822 Board from 23 to 43?
is any changes is done android side app? the application is same copy of nrf Toolbox UART app.
please...
Hi, everyone,
I am developing the project on nRF518522 and I must use the flash memory to save the data. The data must be saved while the device is conncted via BT with...
hi,
When using the UART examples I found that as long as I opened the uart_init () program will not work, debug the discovery process will be executed
case APP_UART_COMMUNICATION_ERROR...
Hi,
I am trying to develop an application which recieves data over SPI and I want to send this data over ble, I am using NUS service. I am recieving 5 bytes over SPI at...
Hello,
I'm using 2 nRF58840 dev kit with SDK 14.2.0.
I'm trying to read the RSSI value of the second board from the first board using LE Coded PHY in both modules.
...
