Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
ble_app_gls_pca10056_s140.hex
Hi,
I am new in this field and i am trying to do current measurement on the nrf52840 PDK using PPK, in sleep mode(sd_power_system_off) i...
Hi,
I have just bought an nRFGo Motherboard (nRF6310) to develop for the nRF24LE1 (nRF2722). I was able to run some example code on the chip like toggling a pin. Next I...
Hello,
I have an application based on SDK 11 and Softdevice v2.0.0. Also there is a legacy bootloader from SDK 11 for performing DFU.
I am wondering whether it is possible...
When I run the UART app nRF5_SDK_12.3.0_d7731ad\examples\peripheral\uart in debug mode, the disassembly window opens, and I seem to get stuck on the second instruction. Step...
I am using a nRF52 and I have to measure two voltages:
the first continuously
when a command is received, the second voltage have to be measured and then...
Hi,
I flashed my nRF52840-PDK with UART/Serial Port Emulation over BLE program. Everything seems to be ok and I can connect with board via Android application. Next I would...
Hi!
I try to send data using advertise PDU and I need use custom 128 UUID.
How to convert to right format service_128_uuid and replace 16-bit value to init.advdata.p_service_data_array...
I'd like to use the nrf52832 as a mesh switch with battery powered. But I didn't find any sample code for the Low power feature in current mesh SDK v0.10.1. Does it support...
Hi,
Dear Nordic experts:
I encountered with a couple of *** issue while configuring SPI port on nRF52832 with PCA10040 demo board. Here I wrap up as below:
First...
I write NRF_UART0->ENABLE = 0x00 in my app in first line code, but now nrf51822 can connect but cannot Download and erase;
in keil it report:
**JLink Warning:...
Hi I am new to Nordic Development. I am developing a product that will use the Rigado BMD-300 module (nRF52832 but no need for FCC compliance testing). The evaluation board...
Hi to everyone!
I'm trying to use the nRF52832 board as master to use an external device (as slave) through SPI.
I take the example peripheral/SPI to start to learn how...
Hi,
How to set the length of the advertising device name? Even i set name type to BLE_ADVDATA_FULL_NAME, i can only able to set maximum of 14bytes. If i increase the name...
