Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hi. My app based on S130_1.0.0 and is run on DevKit with 51422 chip. App advertises and scans at the same time with next params:
adv interval = 20mS;
scan...
im using nrf51822. before entering DFU mode I want to save data in flash. but when I call pstorage within reset_prepare function, it doesn't jump to DFU mode !!!!
reset_prepare...
Hello guys, i'm new in nRF51 DK board, and i would like to flash the .hex file to my board, but when i do it the board automatically unmounting himself and reset with the...
hello there i want to send negative acknowledgement then what should i do?? like i want to send some data and then i want to send negative acknowledgement
i am trying to use yggdrasil for nrf51422 (pca10028) with sdk 10.0. after installing, i cannot see the com port. How do I flash "connectivity_115k2_with_s130_1.0.0.hex" with...
Hi everyone!. I am beginner for Nordic Devices
I want to use RTC Clock with softdevices
so I loaded the project ble_uart_s130 from examples.
and I changed code like...
I have a ble central device. Sending commands to UART in main() works well. Sending in on_ble_evt() doesn't work (only the first char).
But I see in your examples that you...
Hi guys,
I've almost got DFU working on SDK10. However I am having issues at post validation of the image, specifically in the function dfu_init_postvalidate() in file...
Hello all,
Thank you in advance for taking your time for reading this question. I'm developing a proximity application and I have programmed the nRF51 DK with the s110...
Hi,
I am trying to set up a small mesh network. Basically I have a couple of PCA10028 (v1.1.0) and I have flashed the mesh example:
github.com/.../BLE_Gateway
One...
Hello Everyone,
I have been working around BLE profiles for few months and i have made several tested for each service via MCP(android) everything works fine but now i...
Mt need is to do frequency measurement of 0.01Hz to 99.99 Hz
We need a clock of 1us that added to a timer of that start on when the pulse low to high event happens and...
Hi there,
I want to connect multiple nus devices to S120 central. After connection with device, it starts to scan again after the BLE_GAP_EVT_CONNECTED event. And there...
Hi,
I am using the s110 and SDK 6 and trying to have multiple notifications from different services/caracteristics. For now I have two services, one for the battery and one...
