Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Use nrf_modem_lib_init() to initialize the modem, followed by lte_lc_connect() to connect to LTE. However, it consistently fails to connect to LTE. After it times out, the...
HW: 52840DK PCA10056 3.0.1 2023.16
NCS SDK: v2.8.0
I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
Hello.
I am trying to use nRF Connect SDK v2.8.0 and nRF52840 to run Matter's Light Switch and Light Bulb.
I was able to confirm that it works with nRF52840-DK, but...
Hi there,
Our firmware is built on NCS 2.6.1 (soon to be ported to 2.7.0) and uses MCUboot.
I want to set REGOUT0 to 5 (which corresponds to 3.3V) and the `nrfjprog -...
I am trying to upgrade my project which is previously build with NRF connect SDK 2.6.1 to 2.8.0
I am getting this error while building
warning: NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Greetings,
when trying to compile simple GPIO configuration for NRF5340, the compile fails with:
In file included from C:/Apps/NordicSemiconductor/SDKs/v2.7.0/zephyr/include...
Hi
I have set up VS Code (1.93.1) on my Mac (mac OS 14.6.1) with nRF packages and zephyr installed. My nRF5340 DK is also found (however, instead of a nice identificaiton...
I am reaching out to inquire about the support for the indication method in the Nordic nRF52840. Could you please confirm whether this method is supported in the Nordic SDK...
There was no problem when the current version of ccache was 4.6.1. However, the current version of ccache, 4.10.2, behaves differently with the --specs option. It will do...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
What we need is to generate RSA key pairs and send public key to App to encrypt data...
Im trying to get SAADC to continuously sample using internal timer but im getting couple of samples and then it stops, tried everything but I'm obviously forgetting something...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
Hello,
I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
I'm using
the nRF52840 DK and the Matter light_bulb example, SDK v2.7.0.
a raspberry pi with the nRF dongle as a thread border router
the chip-tool running and compiled...
Al over these example programs there are all these messages like
LOG_INF ( "Filters matched. Address: %s connectable: %d " ,
addr , connectable );
How do you actually...
