Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
Hello Engineer Greeting of the day i am building my product using nrf52833 IC , there are some communication modules connected to the 52833 , i want to cheack lowest power...
i have to interface MT29F4G01ABAFDWB in zephyr rtos but i need help how create overlay file for it(i want to interface it using spi), i already have bare metal drivers for...
Hello,
When we flash the BLE Zephyr project to the external chip (nRF52833), do we need to add the SoftDevice controller .hex file as well, or does the merged .hex file...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
When trying to flash the hello world program onto an Adafruit nRF52840 Feather through a j link it fails with "FATAL ERROR: one or more Python dependencies were missing; see...
In any Wi-Fi firmware that I write with nRF Connect SDK I get this error message in my console logs:
<err> net_icmpv6: ICMPv6 handling failure (-2)
This happens in every...
I'm running into this issue quite often where I have a Build failure. I'm sure to others the way to troubleshoot what the issue is may be obvious, but being fairly new to...
i am having a bus fault somewhere in my code, i am trying to use addr2line to identify the source code line that it heppens at, for some reason it shows as if the adress is...
I am trying to connect two thingy:52 and a Polar H10 heart rate monitor simultaneously to nRF9160 dk, but while building the application I am encountering this error. Can...
We are utilizing the nrf5340 alongside the nrf7002 for Bluetooth Low Energy (BLE) and Wi-Fi communication between a wearable device and a host. The host is a laptop connected...
Setup
nRF9160-DK
PCA10090 1.1.0 2022.4
Modem FW: mfw_nrf9160_1.3.3
Asset Tracker V2, I tried both the downloaded version from here: https://www.nordicsemi.com/Products...
hi support team,
in 9161dk, when we need to program external flash, we need to config board with nrf connect, may i ask what's this? and if i need to consider power consumption...
