Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi,
I am facing a power consumption issue with the nRF54L15 (BM15C SoC) in deep sleep (System OFF / low-power state). The measured current consumption is approximately 221...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
Hi ,
I’m working on an nRF5340 using nRF Connect SDK v2.7.99-cs2 . BLE security is configured as Just Works (Security Mode 1, Level 2) on the peripheral .
I’m attempting...
I am using the nRF54L10 on a custom board with a couple of LEDs, a flash storage device and a GNSS device. The application wakes periodically to gather fix information from...
How can I detect when no SIM card is inserted at startup? The purpose is to operate without a connection if there is no SIM card.
[Environ] nRF Connect SDK v3.2.1 nRF9151...
Hello,
I was learning about how the bt_conn references work, how to obtain them and free them, and where they are generated.
I was looking at the central_gatt_write...
Hi
I have currently claimed devices in my nRFCloud I registered two years ago. It looks like this:
It has the mention "powered by memfault" . This is also the nRFCloud...
Hi,
i'm learning l4/e1 and i'm trying to buid the process after finishing step 10 but the build didn't goes through successfully. i got this errors
my SDK & toolchain...
Hello all,
I have an nrf54l15 on a custom board, I am having issues getting a reliable SPI clock signal when using BLE advertisements
This is the clock and correct...
I bought both nrf52 DK with nrf52832 and ISC-nRF52810-A module. I use Visual Studio Code with nrf SDK + toolchain. Hardware connection from ISC-nRF52810-A to nrf52 DK is as...
The openthread coprocessor sample in sdk v2.8.0 and v3.1.0 work for me with the openthread border router but not the sample in sdk v3.2.1
I followed the instructions for...
Hi,
i'm learning the exercise1 for AT commands to control modem and when i apply this command AT%XMONITOR i get the output as %XMONITOR: 5,"","","24202","0901",7,20,"02024720...
nRF52810 program execution failed the CPUID verification. Hi everyone, I have a question. I have a working PCBA with an nRF52810 as the main controller. When reading the CPUID...
