Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hello Nordic team,
I'm developing a BLE peripheral using nRF52833 and would like to validate that my approach for handling connection parameters aligns with Nordic's best...
I now need to make a program on nrf5340 audio DK, SDK v3.0.2 to scan extended adv and print the BASE information in the subgroup in PA, without sink BIS, besides, a smartphone...
Hi,
I am following the course "nRF Connect SDK Fundamentals" and am almost at a standstill when it comes to progress.
I am still struggling with lesson 1 and lesson 2...
Freshly installed VS Code natively on Windows (also tried on Linux and WSL with same result) with NRF Connect Extension Pack, SDK 3.1.1, Toolchain 3.1.1 was used to create...
i get various answer about this, been in the rf design for a while, we used to make global antenna lenght on some give am ook circuit a tad shorter and then use a load cap...
Hi Nordic
I am working with nrf52840 and nrf52832 using ncs v2.8.0
I am trying to save coredump to flash according to instructions on this link - https://docs.nordicsemi...
Hi everyone,
I'm working with the nRF52840 using the nRF5 SDK v17.1.0 and SoftDevice S140 v7.2.0 . My application uses QSPI for external Flash communication.
I have some...
Hi,
i just noticed that for the nRF5340DK board, the file nrf5340_cpunet_reset.c has been removed.
Nevetheless it is still reference in the documentation online: https...
Hello,
We have built a device that uses the nRF52840 reference design shown below. With the configuration shown the board advertises as expected. If we replace either...
Hi, I try to use the example Bluethoot LE Wi-Fi provision in the nRF7002 DK and in the step to see the Wi-Fi Networks in the APP appers internal error.
Development kit...
Hi,
I'm developing a custom window cover device for Matter and I have a weird issue where Matter packets sometimes seem to take a very long time to go though. Window Cover...
Hi, It would have been quite useful if nRF54L15DK had CR2032 battery holder to carry around for experiments. since this board does not have it any recommendation to conne4ct...
I used the device tree to assist with schematic design, but after the PCBA was returned, I found that the peripheral functions could not be implemented normally.
It was...
NCS3.1.1, Windows10, VScode, NRF52840 custom board
With 3.1.1 I've discovered the paths in the "Edit build configuration" wizard are being broken and silently ignored during...
Hello DevZone,
May I know if there are any hardware SoCs and development kits that operate in Wi-Fi Halow(802.11ah) standard? Please point me out if there are. Thank You...
