Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hello, I implemented the function to receive an external 62.5KHz clock as an interrupt and repeat the process at a very regular time using PPI. However, sometimes PPI processing...
Hi,
I'm using SDK 17.1.0 on nRF52833 DK.
Now I want to transmit some data from mobile app to DK board by using examples\ble_peripheral\ble_app_uart.
NOTE: ble_nus_data_send...
Hello Nordic Team,
I have a question regarding usage of RTC. My application is based on nrf52840 and uses BLE + Zigbee + FreeRTOS. From this page: https://infocenter.nordicsemi...
1.I am testing the NRF5340 Audio and fully following the
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications/nrf5340_audio/README.html#fota-build...
Hi,
I tried to use the sensors on the Thingy:53.
However, it looks like the BMI270 on the Thingy:53 is not supported by the nRF Connect SDK because the SDK only supports...
Hello everyone:
I'm following the tutorial in JWT authentication on nRF Cloud | nRF Cloud Docs .
And I want to test the REST APIs by using curl command.
I have created...
Hi,
I think this is a regression or related to this issue:
Attached is a very simple example with the [email protected] - if you build it with `CONFIG_DEBUG=n`, it...
Hi all! I am working in a BLE scanner but I have enabled the filter by MAC ADDRESS. I can filter beacons that are produced based in NRF52 and NRF51. But when i try set a MAC...
Hello,
I am running into difficulties getting the sleep current below 2.356mA. I have a custom board but I went ahead and tested it sleep current capabilities by programming...
Hello,
My application (nRF52832, SDK17.1) uses the fsotrage library for low-level sequential data storage and retrieval.
At the moment I'm using nrf_fstorage_sd as an...
Hi,
I am using nrf sdk for mesh v5.0.0 and we are building our application on top of sensor_server example. I am provisioning the nrf52832(which is acting as sensor server...
Hi Team Nordic,
For setting up a thread network using nRF5340 DK's, I wanted to build and flash Thread: CLI sample from nrf repository. I use nRF Connect for VS Code with...
I’m using the nRF52840DK to communicate with a module over uart. My problem is that the module has a baud rate of 921600 and as far as my understanding the nRF52840 is using...
Hi,
in my current project I need to have a wall clock time, thus I am using the date_time library. While trying to understand it I came across a few issues/questions.
...
