Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
I have to make a connection from a central_uart to 4 periperal_uart every 60ms Sending 30 byte .
I Have to make a polling of all the peripheral every 60ms.
I know that...
Device: nRF52811
Board: custom (EYSNSNZWW module is used)
SDK: 16.0.0
SoftDevice: S112(v7.0.1)
Sample Project: ble_app_uart
Hello,
Is it possible to read BD...
I have a custom board based on nRF52840 with some custom peripherals : LEDs, buzzer, buttons, etc
To get my app working I copied the nrf52840dk_nrf52840 board from the 1...
Hi,
I started using the Nrf5340-DK with the openthread cli sample. It works fine, and now I'd like to move the main UART to pins P0.24 and P0.26.
To do so, I created...
Hello, I've been trying to migrate my code which uses NRFX SPI functions to NCS 2.0
The code compiles just fine on NCS 1.9, but after migrating to NCS 2.0 I noticed that...
I have just been hired to this company and they have assigned me to repair some of their defective modules. The modules are BL651 with what I believe to be nrf52810 processor...
Hi,
is there a driver available for the VM3011 microphone that comes with the Thingy:53?
The chip has some power-saving and wakeup features that are configured using I2C...
Hi,
We are having some issues communicating with a Winbond W25Q64 flash memory. Using the standard SPI Zephyr drivers an attempt to get the Manufacturer ID returns 0xDC...
Hey!
I am working on a zigbee asset tracking system for my thesis. Got myself 3 nrf5340 boards and a sniffer.
Unfortunately i can't manage to get started with zigbee...
Hi everyone!
I have recently been trying to flash the 'blinky' zephyr sample to the nRF5340 Application Core on the R4D4 Control Board. I am yet to have any success, by...
Hi there
I'm using Asset tracker v2 as a base for my application with AWS, however I wanted the FOTA to download to external flash, as the Asset tracker application is large...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 with MCUBoot and want to upload firmware updates for the application core using mcumgr.
I use the hello_world sample in...
We are migrating from Modem firmware version 1.2.x to 1.3.x. Since it is now possible to enable LTE and NBIOT both using the following XSYSTEMMODE configuraton:
How does...
I'm trying to develop a Bluetooth mesh network with low power consumption.
Is the performance the same when comparing firmware using the nRF5 SDK for Mesh and firmware using...
Hi,
I am developing the nRF52833 DK with NCS v2.0. The goal of the application is continuously send temperature data (using health thermometer service). I am currently trying...
