We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,Nordic engineers:
I am using the nRF52832 chip and the nRF SDK v17.1. My device operates in a dual-role (central/peripheral) configuration, and I am using the Nordic...
Title: SoftDevice Controller: 100% connection establishment failure (HCI 0x3E) with SKY66112-11 PA active
Hi Everyone,
I am working on the following development project...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design and I have two questions about the QM13345 configuration.
1. LUT
The Thingy...
I have been testing the HTTP FOTA procedure as documented here using the 1.5.0 test diffs as provided in .
Many of the messages output by the modem in this upgrade process...
Hello,
We are seeing a west build reproducibility issue on nRF Connect SDK v3.4.0 that we have narrowed down, through extensive elimination, to the compiler's code generation...
**Setup**
- Custom board, **nRF54LM20A** , first bring-up. The SoC is powered from an
nPM1300: BUCK1 = 1.8 V feeds VDD.
- External **J-Link** (firmware compiled Jun...
Hello,
I have a tight loop with strict timing requirements that I'd like to run on the FLPR core of the nrf54lm20. In each iteration of the loop, i need to write data to...
Hi，
When we draw PCB, we also need to design it like your DK board? There are several square copper skins under the chip, the middle of which is grounded, and the other...
I have nrf52840 DK board, running cutom image that implements BLE central, constantly scanning on coded (S8) phy. Trying to add NFC T2T tag, and it doesn't work. Disabling...
Hi,
While characterising low-battery behaviour of the nPM1304 on the nPM1304 EK I see the following:
1. With VBAT above ~2.4 V, Ship mode current is ~0.40 µA, as expected...
In the bare metal SDK, for the cgms routine, if we switch to the internal LRC, how should we configure it?
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC =y
After making this configuration...
Hi! I know that FindHub is supported on nRF Connect SDK, but I'm wondering if there is any support for it on nRF5 SDK for the nRF52840? The use case would be adding the feature...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
