Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
For Errata 149 on nRF52832 , TWIM send illegal pulse after clock stretching.
When using TWIS as slave device and TWIS require clock stretching,
Do they work correctly...
I have an issue with DFU via USB CDC ACM.
I would like to update the firmware using open bootloader over USB without softdevice.
I already tried to follow the thread:...
Hello,
I have a firmware working perfect with nRF52832 DK and nRF52840 DK, using SES 5.40a.
Now I just upgraded SES to version 5.70a. With new SES version, each time I...
Hi,
we are getting during NB-IoT attach (full AT dialogue below) for some nRF9160 SIPs:
URC: +CNEC_ESM: 29,0 URC: +CNEC_EMM: 19 URC: +CEREG: 2,"B414","000F6E21",9,0,19...
Hello,
I follow up this documentation https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/ug_thingy91_gsg.html#updating-firmware-through-external-debug-probe...
I try to run asset_tracker and asset_tracker_v2 on nRF9160DK. I observed that the default cloud Host Name is Amazonaws.com, which is shown in autoconfig.h file. see the image...
I tried to debug Asset_tracker_v2. During step by step debug, the program navigate to that part which is not included .. see the image. Also, I want to know, little more:...
Hello Devzone Community,
My name is Ted, and I am some way along development of Zephyr based firmware, running on an nRF9160 based custom board. I'm looking to put the board...
Hi,
How can we prove that the A-GPS is working correctly? We have run an experiment where we have use a module with A-GPS and one without and they have very similar (and...
Setup -
1. Sample used - nrf/samples/nrf9160/lte_ble_gateway
2. Board used to build - nrf9160dk_nrf9160_ns
3. NCS version 1.9.1
Steps performed -
1. Built the...
Hello Everyone,
I am trying to implement one wire protocol for interfacing MAX17211 fuel guage IC with NRF52840. I wand to know if there is any one wire library or any example...
Hi,
Do you have a suggestion for a 2.4GHz chip antenna? I sent a board to Ketil for RF tuning but the meander antenna ended up as too short. We would like to avoid a separate...
Hi there, I have been always using the dev board BLE antenna for the nRF52832-QFAB.. but now i need to reduce much more the size of the board, so i need a much smaller antenna...
