I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
I'm using nRF connect SDK 1.7.1 with ZephirOS.
I'd like to configure input / output to be redirected to UART and mirrored to USB CDC/ACM.
The reason is that I...
(nRF Connect SDK, v1.8.0, nRF52840)
I would like to create classic Bluetooth Classic peripheral behavior, the peripheral is not advertising (or advertising without name...
Hi, I created a Zephyr project for board : nRF5340DK_nRF5340_cpuapp . Now, I need to read the Device ID from FICR. I made changes in overlay file as shoen in atached first...
Hi,
I am using SDK 17.1.0 as a host scanner. When I changed the timeout to 0, there was a problem with the connection slave (NRF_ERROR_INVALID_PARAM). I'm pretty sure the...
I'm currently using: - NCS 1.6.1 - Zephyr - NRF52840
I'm using the lwm2m client to read and write to lwm2m objects.
When the device starts for the first time, I store...
Hi,
I downloaded the hello_world_with_mcuboot.zip file that Simon provided in one of the ticket few days ago - Case ID: 283917.
I built hello_world_with_mcuboot project...
Hello,
I would like to know if the application / use case stated below is implementable.
In my application I would like an nrf52840 to communicate with the Bluetooth module...
hi,
In the NUS routine, it is necessary to turn off the peripherals before entering the idle mode to minimize the power consumption, but there is no change after adding...
Hi,
I'm trying the sample fat_fs on the nRF5340 DK
1) It does build, but there is awarning
CMake Warning at D:\nRfConnect\v1.8.0\zephyr\CMakeLists.txt:722 (message)...
On a MCU PCA10040 v2.0.0, I ran the command:
.\nrfjprog.exe -f NRF52 --program .\final_image.hex --verify --reset
Which subsequently caused the board to go into a reset...
I have a Thread bench-top environment set up that includes
One nrf5340dk flashed with the openthread coap_server firmware build and flashed on 1.8 via Visual Code
Two...
Hi
If a bug stop the application to feed the wdt,Is there any way to store 8bytes application data to flash before reset which occurred by wdt?
I find that there is only...
Hi,
I'm having some difficulties understanding how to manage commands in endpoint-specific callbacks. For example, when receiving a "ZB_ZCL_CMD_CONFIG_REPORT" I'm able to...
Hello,
I have a peripheral (nRF51822, S130, using the peer manager) that should be paired/bonded with one or many centrals. I have followed the example ble_app_bms from...
