Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello, sir.
I used to work on twi0 and twi1, but now I'd want to shift both twim0 and twim1. However, I'm getting an error saying that 'NRFX TWIM1 INST IDX' is undeclared...
Is it possible for nRF Connect iOS app to display devices that were connected/paired through the iOS Settings menu? The problem I am having is when looking to perform DFU...
Hi iBasis support,
I'm having a billing issue with your website. I'm using the iBasis card with the NRF9160DK board.
When I ran out of data, I just follow the link on...
Right now I use the app_timer_cnt_get() method to get a current tick count. It appears to return a counter that increases with 32768 counts per second. However, it overflows...
Hi,
In NRF52832 i have integrated IMU sensor and and DPS sensor . i have build code and Run .
But after 2-3 minutes its stucked . so then i pressed the pause button ....
Hi, all
My custom board has nRF52833 mcu and wifi module(esp-wroom-02). I'm going to communicate with these two using the uart port.
The problem is, data communication...
Hi there, I am working with an application that uses the NRF51 chip (through the Taiyo Yuden EYSGCNZWY BLE module) and am trying to implement buttonless DFU. I am having issues...
In the latest release v1.8.0, there is an example ( Mesh and peripheral coexistence) which also has th e extended advertising.
However, it seems that the BLE Mesh stack...
Hello
I'm using multiple nRF52840-dk (SDK17.1.0, Windows, Segger, S140).
I'm trying to make BLE device(nRF52840-dk) that automatically connects to specific BLE device...
Hello,
I am using nRF5340 Audio DK devices. I am programming two (2) devices as 'Gateways' and one (1) device as a 'Headset'. I have two questions related to this matter...
Hi,
My project (under embedded studio )works if running on a chip with the register FICR INFO.VARIANT = 0x41414330
but freeze on a chip with the register FICR INFO.VARIANT...
I can't flash/write my nrf52840 Dongle under Linux with nRFConnect v3.9.1 with Programmer v2.0.1
The buttons remain greyed out, the left window does not display any information...
I'm following the heart rate sensor example in the VS Code Youtube Tutorials series, and there are some pretty straightforward prinkt statements in main.c, such as 'Bluetooth...
I'm getting data from peripherals, and I need 96KB/S to get to the NET layer, because the other side needs to use data in real time, but the data transfer is too slow.
So...
