Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I am trying to minimize the power consumption on a NRF52840.
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf52-designs states...
nRF52840 can support matter (BLE + Thread).
it is noted at https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
even that have a demo...
Excuse me：
How to get profile QDID，host QDID and controller QDID of nrf52832？The current SDK version is nRF5_SDK_15.2.0_9412b96,Soft device is S112,thank you!
My goal is simple. I want my nrf5340DK to communicate with my nrf24L01+ Just to test the water and also because I have experience working with the nrf24 modules. Is there...
[ Problem ]. When communicating with the TestApp as shown below, it is taking an unusually long time to get a response. The problem is that the response takes more than 0...
Hello,
I’m currently trying to flash the blinky code (found in the ‘Getting Started’ section) onto the nordic nrf9160-dk.
The error I’m getting is :
“error: cmake...
Hello,
We have a development team in Kiev, Ukraine.
We see that LTE over nRF9160 is not working there.
Is it possible that LTE over nRF9160 is not supported in Ukraine...
Hello
We are using secure boot loader for DFU and is working great. We were using single bank DFU, but reduced our image size to allow dual-bank DFU. If you could please...
Hello Nordic Devzone Community,
I am developing an out of tree driver for firmware running on an nRF9160. I've made some progress and am getting closer to correctly implementing...
Dear Sir/Madam,
We are trying to lower the low frequency crystal start-up time.
https://infocenter.nordicsemi.com/topic/ps_nrf52840/clock.html?cp=4_0_0_4_3
In the description...
I'm wrapping up a job for a client and we are squashing the last few bugs, but I can't seem to understand one of them. Pin 0.13 of our nRF52840 is pretty simple, just a button...
Looking for wisdom on wiring up the nRF (52833, via Raytac RF module). I'm having a hard time understanding (PS, Hardware Layout) section how the different power Configurations...
Hello,
I have previously created a product using the nRF8001 chip a year ago using a PCB antenna design. At the time the enclosure for the PCB was RF transparent and the...
Hi everyone,
I am getting start with the GPS and LTE connections on your nrf9160dk platform. I have tried all of the samples I was able to find but I get some weird results...
I'm running the Serial LTE Modem firmware and utilizing the reference docs in the LTE Link Monitor Terminal (My commands in yellow, blue/grey text is response)
NCS 1.4,...
