I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hello,
In my board, nRF52832 is connected to other MCU.
And those two communicates via SPI. nRF52832 is master.
To synchronize two boards, MOSI pin has to be used...
Hello,
Central uses nRF52840, and multiple peripherals use nRF52832.
The central is paired with each peripheral device , and each communicate.
To do this, I am developing...
I am testing smp_srv (bluetooth) with NCS 1.3.2. I don't know how to build and flash related apps for MCU boot in NCS. MCUboot is unable to boot smp_srv even after running...
Based on nRF52 hardware，I want to develop a phone based on HID protocol to control the phone, send instructions to let the phone into the lock screen state，
How to go about...
Hi, DevZone, thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
TARGET : nRF52840
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
...
To whom it concerns:
I'm a little new to Bluetooth SIGs launch studio and need a little guidance on the correct QDID to utilize for my product using Nordic SDKs.
I have...
Hello,
I'm working on a program that receives the temperature over TWI, saves the temperature in a string to flash memory, then adds this string to an NDEF message to be...
Hello,
I have 4Pcs same PCBAs and same firmware, the current values as below:
2.2uA
3.3uA
3.0uA
3.8uA
Condition: Power Supply 3V Battery; Temperature 22...
Shalom!
We have a nRF9160 custom board on which I cannot switch some of the IO lines.
For example we have two leds, P0.9 an P.10 but only P0.9 works. The hardware guy...
Hi there, now I set up a BLE to connect peripheral to central via NUS service. The peripheral is a customize board with nRF52832 and the central is nRF52840 DK board. The...
Hello everyone I hope summer's kind with you (or winter, for the southern hemisphere...)
Here's the deal: my printf and NRF_LOG_INFO output zeros, while my register clearly...
Hi Nordic team,
I am using nRF connect sdk mesh light_switch example. version of sdk is v1.6.1 .
The node is detected in the nRF mesh app in my mobile.
what does group...
I believe I'm following both the Cypress data sheet properly. Yet I'm still having an issue getting the simple QSPI Peripheral example to show data consistency.
Can it...
Hello
I want to operate SSD1331 OLED(96*94) using sdk v17.0.2 and nrf52840 custom board.
The OLED example of sdk v15 was replaced with the codes of sdk17 and tested on...
Hi Nordic experts,
Recently, I consulted the datasheet and tried to find out something about the radio speed when using softdevice, unfortunately, I can't find anything...
