Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hello Nordic Team, I am working on a LE Audio project on NCS v2.9.0. My development board is nrf5340-dk. I am using unicast client example and I am trying to use it with my...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Hello, I have recently switched to nrf52840 dongle for 802.15.4 sniffing.
I did a simple test with a ZigBee Green Power sensor sending data on channel 11. On the receiver...
Hi,
I am using a nrf52840 dongle for sniffing the bluetooth connection between 2 devices. These are the wireshark logs
What I could see is it initiates the pairing with...
I have a custom board with a nrf9160 on it that has been working for the last three months but last week when i was evaluating low power modes on the board i couldn't talk...
Hi,
i am using SDK version 2.1.1 and recently we had a problem due to the errata 160 which is fixed also in SDK 2.1.4
I am using Toolchain Manager 1.5.3 and i cannot select...
Hi,
we plan to use the nRF52832 in a new project, where we will need ANT support.
I've seen that it is possible to use the nRF5 SDK and the SoftDevice 332 to have ANT...
Hi everyone, I have a problems when I build custom board NRF54L15. I build this project for custom board for nrf52833. It's okay and no error. After that, I change this board...
Hi!
I am testing the nRF54L15-DK with 2.9.0 SDK and have some questions:
1. MX25R64: - why is it used in 1-bit (spi) and not 4-bit (qspi) mode? - OTOH this setup saves...
I have issue in newest SDK 2.8 of nRF Connect for VS Code. When I change something in prj.conf or in the source code, I often have to build and compile two or more times to...
I have looked at forum_post_1 , forum_link_2 and forum_link_3 . In short, I am following instructions for my_dongle . I have ncs 2.6.1. I have clones of nordics git repos...
I notice in github.com/.../nrf802154_sniffer.py that there is a line saying: TODO: Add toolbar with channel selector . I know extcap supports these toolbar controls and a...
Hi
At nPM1300 product specification V1.1 page 148(8.1 Schematic)
The control I/F between nPM1300 and nRF5x is TWI(I2C), and there is four signals(SCL, SDA, Reset, INT...
