Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I2C burst write for nRF5340 at 100kHz is failing with a reply of -5. (Trying to use the BMI270 drivers sample, it will fail during reg_write of the configuration file)
Reading...
hi
I have nRF9160 dev kit, which I am using in a LAB with a private LTE SIM card, which has 99920 PLMN ID.
The network supports Band 3, and NB-IoT is configured as an...
Hello everyone,
1st of all, thank you for taking your time to have a look over my "problem".
I have a device that I am working on, that acts as aperipheral, it is...
I modified, My application's bdaddr is set public device address. secure bootloader's bdaddr is set same public device address.
When run DFU on nrf connect for desktop,...
In my application, I am unable to read back the publish address which was configured during initialisation through mobile.
Please suggest any APIs.
Device: nRF52832
...
HI
The SDK is "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0" and I find a question that is: for all thread programs, add nrf _ delay_ ms () function in while (true) will affect...
I use a sample in NCS1.5.0 to start my project . but examples in NCS1.5.0 are single ble service .always like these: bt_conn_cb_register(&conn_callbacks); bt_enable(bt_ready_cb_t...
Hi,
1. I see the following differences between VDD1 and VDD2 descriptions:
nRF9160_PS_v2.0 P385
2. What are the differences between VDD1 and VDD2 features?
Thank...
Hi all,
I am trying transition from SDK 15.0 to 17.2 and having a branch instruction to itself (an infinite loop) which I think has something to do with the adjustment of...
I would like to create SPI clock timings using the following documents. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fspim.html&anchor=topic
1. CSN...
I'm trying to figure out a strange issue with GPS. We have a pretty well debugged and stable system that we're adding some features to, mainly GPS. We're on SDK 1.5, using...
Hello!
I am developing an application which is connecting to an nRF52 board using the Android-BLE-Library implemented by Nordic The application is doing the following: ...
I was looking at nRF52833 as a candidate to use it as a BLE keyboard and USB keyboard (as it has USB2.0)
But in the API documentation section I see that HID keyboard is...
Hi,
I am developing a product using HA.
I am using SDK 3.0 and nRF52840 Dev-kit.
I am using the thermostat cluster, basic, time, power config, and OTA.
Along with...
