Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello Nordic Family.....Greetings.
i am Trying to add PB_GATT provisioning in the UART coexistence example of mesh sdk v4.2.0 .
i have Added GATT related files to project...
I have done the ble_app_blinky example, for both central and peripheral. I press button at central and LED glow at peripheral and vice-versa.
I am struggling in using the...
I'm trying to update the modem firmware on my nRF9160-DK through the Programmer app available in nRF Connect (v3.6.1), but the app is returning an error, saying it cannot...
Hi I'm designing a board based on nRF9160 that inspired from Thingy:91. I changed the LTE antenna to Molex 2067600001. Now I need to know that can I use the same external...
Hi , i would like to send some sensor data coming from SPI interface and then send it from one nrf52832dk onto another nrf52dk or a nrf52dongle and on the receiving end send...
I am currently using softdevice s140 v6.1.0 with my nrf52840 product, and I am occasionally running into a Softdevice Assert located at 0x000154A2 while the device is advertising...
Hi,
I have a wifi chip MTk7628 that communicates over a usb to ttl chip cp2104 to the NRF52832. I was able to cross compile the heart rate collector and burn the OpenWRT...
Hi Team,
Why the RX selectivity performance is different on -MHZ and +MHz?
As I know, Rx selectivity (or call adjacent channel rejection) performance shall be equal or...
Is there a simple way to have linux time up and running with minimum current consumption and good accuracy?
Preferably, some class with get_unix_time and set_unix_time...
hello Nordic
i am working with the nrf52840 , sdk 16.0, s140
i am using the peripheral ble_app_blinky example as a base
i added saadc and twi, (spi and uart will...
Dear supporters,
I am designing an antenna for the chipset NRF52832. After several experiments indoor and outdoor environment, we got some issues. Besides, We got the same...
When I call sd_ble_gatts_hvx() it returns 0x3400 and I'm not sure why. The error indicates the sum of these three errors:
NRF_ERROR_STK_BASE_NUM (0x3000) NRF_GATTS_ERR_BASE...
Dear Members,
I tried to include temperature into my ANT HRM receiver code,
but when I add components\drivers_nrf\nrf_soc_nosd
I got plenty of errors, what do I...
Hi,
Using 'nrf5_SDK_for_Mesh_v5.0.0_src' exampe project 'light_switch' developed for nrf52 Development Kit(pca10040). How to make the same project working on Thingy52(pca20020...
