Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello,
I'm trying to recreate the PWM_library example from the v.11 SDK in a new file in Keil. I have compared the debug settings in my project to the debug settings to...
Hi there,
I am following the thread to use JlinkExe and JlinkRTTClient. I encountered a situation which i don't understand.
After running JlinkExe (go to the folder...
Hello,
I am trying to remake an nrf52 project in Keil and ran into a problem regarding stdint.h. There is already an "include <stdint.h>" statement and Keil has not reported...
Hi,
I am testing the NUS using the UART example in the SDK11 with the PCA10040 board.
Since I want to achieve the maximum speed of transmission I used the FIFO buffer...
I am having issues waking up nRF52 with s132 using the RTC interrupt. The same code is used on nRF51 with s130 and does not show this behavior.
The RTC is configured and...
Hi,
is it possible to have the same configuration as in the example ble_central_and_peripheral but with ant+ as peripheral (on nRF52)?
Thank you for your attention
I am doing externally triggered SPIM transfer on the Nrf52 using PPI.
I found that the NRF_SPIM_TASK_SUSPEND is a very power hungry operation as SPI suspend waits for the...
Hello
I have a nRF52-DK and I am trying to programme an external designed by myself but this one contains the nRF51422 chip. I am using nRFGO Studio to upload the .HEX...
I consider using " nRF OpenMesh " to implement my project.
But, I have no idea bout what's the throughput of it.
Anyone has an idea?
I find the max. content of advertisement...
Hello, I'm trying to make two nRF52832 connect to each other on their own. Currently, it seems that the ble addresses are reversed when printed by ble_gap_addr_print in different...
Hello,
I'm looking for a solution to achieve best possible resolution timestamps of received advertising packets for BLE. Is there any specific chip that you would recommend...
Hi there!
I searched the forum and didn't find any clear answer.
nrf52 programming pins are SWDIO and SWDCLK and chip can be programmed.
When nrf52 is part of a pcb...
HI,
I am trying to Port the BLE BEACON source code of PCA 20006 to PCA 10028 EK.
I have changed the IROM settings.
I have initialized the soft device handler to NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I am trying to understand how can I have a running counter based on the low power 32.768 KHz oscilator that does not trigger any timeout interrupts (I am using the soft...
