Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi,
I am trying to get the MQTT publisher example working on my nrf7002DK board. For this, i have done the following things
- SDK version: 2.6.1
- Board selected: nrf7002dk_nrf5340_cpuapp...
1. What is the antenna output of the DECT NR+? Is it the same pin as CAT-M/NBIoT antenna output? (i.e. pin 35) 2. In Section 8.3 of OPS document about DECT NR+, it mentioned...
Hi,
I am having similar error as reported in Case ID: 308488, however here issue is running z-test on provided Nordic test samples.
(note: nRF-connect SDK, works as expected...
Hi, I have a question about SDK. Why not a single example build out of the box in SDK. As a beginner to learn about nRF devices, if i have to face all these weird issues in...
I would like to monitor the states of switches sw0 and sw1 on my nrf7002dk board using GPIOTE interrupts.
Initially this is just for example purposes.
I eventually need...
sdk: 2.5.1
cpu: nrf5340
I have a bootloader which have a big ram block for upgrade purpose (around 250kb) in bss section (I will move it in noinit, but it is not the point...
Hi,
I am using nrf52840. we have already used 3 SPI instance (SPIM1, SPIM 2, SPIM 3). wanted to use one more SPI instance i.e. SPIM 0. but if I enable this I am getting...
Hi,
TWIM does not work well with nRF5340DK as shown in the subject. The conditions are shown below. - I/O voltage is not 1.8V. The waveform is distorted around 2.5V, though...
Hi,
We are developing a device using the nRF5340 DK and need to add external Flash memory accessible via QSPI with XIP, as the available memory is insufficient due to DFU...
Hi all,
I am very new to the nRF controller. Previously, I have worked with STM32 controllers.
Currently, I am working on a project with the nRF5340. I am having difficulty...
Hello,
In the past, i have posted a ticket to ask can the CIS and BIS modes work simultaneously. The answer is that it is feasible in the future.
Can CIS and BIS modes...
Development Software: Segger Embedded Studio, nRF5_SDK_17.0.2_d674dde
Project consists of an nRF52DK-based peripheral (remote control) and a custom nRF52832-based central...
Hi,
I have a project that uses nRF5340 with MCUboot and multi image update configuration. The update works, but today I noticed that the pcd_sram RAM region seems to be...
