Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Using NCS SDK v2.1.0
Example Project: nrf/samples/bluetooth/peripheral_power_profiling
Building the example project gives build warnings:
Could you help me understand...
Hi,
I am trying to implement a Low Power Wireless technology to get sensor values from more than 10 devices at a time. On doing research, I found that the Thread Topology...
Hello, we have built a custom nRF9160 board with different populations for the GPS antenna, now we would like to do some tests to find out which variant offers the best signal...
Hi!
The posts I've found regarding this were quite old, and they mentioned features which then were coming.
So I'll ask anew: Is it possible to use AT-commands through...
Hello,
I would like to ask you if SoftDevice S132 v.7.x.x allows Master-initiated Feature Exchange procedure?
BLE Core spec: Vol6, Part B, Cap. 5.1.4.1.
I tried to find...
Hi everyone, I use nrf52833 to make dongle. My test found that after suspend of usb, I tried to enable ESB rx mode, but I couldn't receive rf data. What is the problem?The...
Hello,
When deleting a bond from the central, after trying to reconnect with the peripheral the PM_EVT_CONN_SEC_CONFIG_REQ gets called as expected. I know that allow repairing...
I have been trying to develop a project, my custom board has a nRF52840 chip and I have a nRF52840 DK too.
My problem is when I try to debug any example from any SDK....
Hi, I attended the Nordic Seminar in Tel Aviv last week and heard several lectures from your experts.
It was recommended that we use a module with Nordic IC rather than...
Hi,
I am using vscode and nCS on windows, kindly help me with below 3 queries:
1. How to generate a binary signing key, say "KEY_1"..?
2. How to sign a binary with...
Hi,
We are trying to use PPK2 to measure current of our board, we want to receive the data from PPK2 and parse by our owner python script, so could you provide the protocol...
Reading The adhoc smart waste solution uses the nRF9160 SiP I tried to reproduce the mention 6 µA with LTE-M in eDRX with an interval of 655 s.
I use
CONFIG_LTE_EDRX_REQ_VALUE_LTE_M...
Hi,
We use PPK2 very conveniently as a logger for testing.
How about adding the supply voltage as display options also?
We hope you will consider this.
Thank you...
Hi dear,
It is possible to establish parallels multi connection to different J-LINK's devices serial numbers via nrfjprog.dll, or any other automated way ?
We successfully...
