Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi,
I have two nRF52840-DK boards. I would like to make these two boards as BLE Sniffer.
- #1. nRF52840-DK, Sticker Info.,PCA10056/ 2.0.1/2020.43
- #2. nRF52840-DK,...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
prj.conf CONFIG_BT_MAX_PAIRED=4 CONFIG_BT_KEYS_OVERWRITE_OLDEST=y
If Nordic BLE reach max pairing, BLE delete its pairing...
For study purpose, I try to change bootloader to move APP offset by
change APP start address to 0x20000
change start_addr in nrf_dfu_mbr_irq_forward_address_set() and...
Hello,
I am trying to send "Hello" through the UART and the nrf52840 dongle using a USB to TTL approach. The main.c code and the sdk_confg.h are uploaded here. The problem...
Hello,
I love the Online Power Profiler for BLE! Great tool, very useful and well done!
I have one request/suggestion... when scannable advertisement is selected, it would...
Hi,
We develop in an OpenSuse VM so that we all have the benefit of only having to setup the tools once. Segger Embedded Studio was building our variant of the DFU Bootloader...
Hi, I am currently working on nRF52840-DK board and trying to implement simple programs. I want to toggle a LED(P0.13) on the press of a button(P0.11) but I dont want to use...
Hi,
I am trying to DFU OTA by using nrfutil with nRF52840 dongle.
I have already write nRF connect desktop Bluetooth into dongle, but when I use nrfutil to do DFU...
I am using: nRF52840 nRF Connect 1.9.1 VS Code W5500 for ethernet Azure IoT Hub
I have the above (mostly) working. My code is based on the Azure IoT Hub sample for the 9160...
We are developing a device where we would like to include the bluetooth connectivity of the device with phone, to answer the calls and to listen to audio. We are using nrf5340...
Hi,
actually we have following Solution:
- NO battery powered devices - the first nrf58240 acts as a beacon advertsing temperature values all 10sec - On our gateway, there...
Hi,
I'm trying to follow the MCUBoot + SMP SVR example on this page: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
My application uses NVS to store data and it works just fine - no errors reading or writing , and saved data persists between device power cycles.
My application also has...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
