Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hello,
We have a physiological monitoring system in production where we used NRF52832 as a peripheral. Connecting this peripheral with Windows bluetooth, we realised that...
Hello,
I'm currently looking at using a last will message that updates an attribute on the cloud if the device disconnects from the broker. The broker and client agrees...
Hello everyone,
My current setup:
1.Development Kits = NRF52840
2.Nrfutil Version = 6.0.1
3.Softdevice = S140
4. Operating System = Linux
In current goal is to...
Hi There,
I am currently using a custom bootloader for my devices which was started from the secure bootloader example given in the SDK, I am using BLE as the transport...
i have nRF Connect SDK v1.6.1，excuted “west update” and “west zephyr-export” command（the project will not built successfully without executing these 2 commands）
then i was...
ncs version 1.6
SES
Windows 10
I have installed ncs completely using standard tools.
Now I am following the tutorial Part 1.
The project hello_world is created...
Hi,
I have a GPIO used as input or output. When it's used as an input (99% of the time), I have an interruption on it (falling and rising edge).
When I use it as a output...
This is my first time using Nordic SoCs, so forgive me if this is a silly question. I have a Fanstel BT832X evaluation board (model EV-BT840(832)-V4). I tried the Nordic's...
I upgraded the code from sdk13 to sdk17.
The setting is the same as the original code and there is no error.
However, if I build, the original code is built with the app...
how am i going to merge ble_app_multirole_lesc and ble_app_blinky
I add
into ble_app_multirole_lesc main.c
and it stuck in services_init()
seems like the err_code...
Hi,
I would like to make a system that goes to sleep for a while and wakes up for a short time thanks to the rtc. According to the documentation, the power consumption of...
Excuse me：
PPK2 doesn‘t work，I don't know why，The computer does not recognize the usb port after connecting the USB cable，The indicator light of ppk2 is not on.What should...
Setup:
nRF PPK2 is connected via USB to the port DATA/POWER to the PC
Running nRF connect version 3.7 from ubuntu 20 causing the following issue, when using "Power Profiler...
Hi, I'm having issues programming my Thingy91 via the NRFConnect programmer app.
The Thingy in question has had various applications run on it over time, but the objective...
Hi,
I am currently setting up an MQTT client via the MQTT publisher sample on zephyr.
My mqtt client is a NRF5340 and it is connected via ethernet with my pc and also...
