Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hi,
I want to make a bluetooth mesh system with over 400 bluetooth devices. As I know the Nrf52840 Dongle can connect to 20 devices concurrently, so if I use 20 Nrf52840...
Hi
Am trying to establish nrf52 DK as peripheral with nRF connect application as central but am unable to establish connection between both.
Please debug the following...
I've been using the CLI and also piping NRF_Log thru the same backend. In my application there are alot of time critical operations. I've noticed with some GPIO toggling for...
We have a device with firmware based on 14.2 (with sd-id 0x96) and we're trying to do a DFU over BLE to a firmware base on 15.2 (with sd-id 0xAE).
We can do a firmware update...
Hello:
I've got a application where I want to detect if the NRF52 is near a NFC reader. I don't need two way communications, but it would be good if the reader could modulate...
OK - so I just started with these chips, and have been asked to find out why SWO debug signal is getting corrupted.
At fairly random intervals the signal passive state inverts...
Hi,
I'm having problems connecting to my device, because whenever I do so, the SoftDevice asserts at address 0x12CFA.
I use softdevice S140 v6.0.0 and SDK v15.0.0.
I...
SAADC can't measure input voltage higher than VDD voltage. External battery (18650) voltage is higher than on-board VDD. There is very good article on your site explaining...
HI All
Im newbe in on that "field", so im apologize for stupid question.
I will like to check a optimal casing for my new product equiped with bluetooth comunication....
Hi,
I'm having trouble writing a long characteristic. I'm using the pc-ble-windows code from https://github.com/NordicSemiconductor/pc-ble-driver . I've compiled this and...
Hi,
I am using SDK15.2/3, I know the SDK peer manager has a feature to delete the oldest bonds if the flash memory is not enough to store a new bond. In this case, whether...
I want to transfer some data stored in nRF51822 to another BLE central device. I guess the idea is very similar to "ble_app_uart" example except that I don't need the part...
Hi. I have a project based on multi-link central with NUS service.
I can connect to multiple peers ok at the same time, disconnect etc. However if I am connected to one...
The Declaring attributes section of Zigbee stack API overview ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v3.0.0%2Fusing_zigbee__z_c_l...
Interfacing to CC3100 and need to send socket data over spi that is 1400 bytes.
Assuming I would need to send 200 bytes X 7 and try to get the list array to work.
But...
