Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make my code now interface to the SDK only through the API, but at the moment this does not suit my requirements.
In particular I have issues with the implementation...
Hello. I am using the nordic thingy 52 sdk to program my thingy. I have seen that the temperature values are sent to the client based on a timer. I wanted to ask if there...
Hi team,
Some questions from my customer as below regarding on ZigBee MAC address usage, could you please help to clarify?
Q: If a Router wants to obtain a new device...
Hi,
I have an application of memory size 380Kbytes, I could able to upload application into a device which has nr51822. After checking the datasheet of nrf51822 I noticed...
Hi,
I have a problem with the nRF52832-QFAA-R7 chip on a developed board. The chip can be programmed via SWD, but then neither the DFU mode nor the program starts. For the...
Hi,
I need to develop a proxy client using the Nordic SDK, running a central device role using the nRF52840. The central device will connect to already provisioned nodes...
hello folks
I'm triyng to send a simple vector with ble but what i receive was different.
aniway what i want to send is something like this:
dati[0]=0; dati[1]=0; dati...
Environment: - SES 4.12 on Windows10 - SDK 15.2 - nRF52840 on custom board - PCA10056 hot-wired for SWD to the custom board for JLINK (sorry Segger, I'm cheap)
I was having...
Hello,
I have a working code to read data from BMI160 an IMU sensor. The data is sent over BLE. Is there any way I can display the int16 data as it is in android or windows...
I'm trying to read a voltage from my power supply using the differential SAADC on my board to simulate the readings from a thermopile that I ordered so I can start calibrating...
Hello,
I am working with nrf51822 and I want to send data over ble to an android application which requires pairing. I modified the ble_app_uart example to read the data...
Hi Nordic Forum!
We're currently tuning our antenna since we runed with some problems during our EMC testing.
In that regard, what is the impedance (both input and output...
Hi,
Is there no specific code of ble_app_uart_coexist meant for PCA 10056 and eventually s140?
Or will the same code work for the nRF52840 board?
I am using SES and...
I want to use the nordic USB peripheral drivers to allow for the initialization of multiple devices. The end result of the project will be to have a single nordic creating...
I am using the nRF52832 (on Rigado BMD-300 EVAL kit). I am using keil IDE and nRF GO to upload my compiled code to my device. I am using SKD 15.2.0. Using Windows 10.
...
