Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello I am happy to you to read this text...
I meet a problem...
when I want to work nrf51_SDK_10.0.0/example/peripheral/blinky/pca10028
so i clicked "Rebuild" but...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi all,
I would like to setup a system where a single central BLE device (a smartphone) has to talk sequentially to several BLE perihperals (Nordic chips).
I need to...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I made timer(repeated) as below.
void init_timer(void)
{
uint32_t err_code;
err_code = app_timer_create(&m_timer_id,
APP_TIMER_MODE_REPEATED...
Hi,
I have a nrf51-DK, and I use softdevice s130_1.0.0 with keil c 5.18a,
My project with custom service uuid "DFU" and custom uuid "my_uuid", and battery uuid, alert...
Hi,
I've noticed that in the examples that come with nRF5 SDK11 there is a template for creating BLE peripherals (ble_app_template). I was wondering if a similar example...
Hi.
I'm using PCA10028, SDK10.0.0, S130 as central.
After connection, if i want to change SUPERVISION_TIMEOUT, is it possible?
If it is, how can i do that?
I need...
Hi.
I am trying to get the RTC started, and I've followed the rtc example in the NRF51_SDK.
But things go wrong when I call:
ret_code_t err_code = nrf_drv_clock_init...
Hello , RX: nrf24LU Tx: nrf51822 use ESB Lib. But the nrf24 Can't receive data continuous.
if I Want receive 2th data , I must power up the nrf24.
This is my Code :
RFCTL...
hello,
I wanted an info which tool is better for debugging when using
native SDK.
do i have to use pyocd or openocd for native sdk hardware debugging
and if you can...
Based SDK 9.0 "ibeacon" example, nRF51822(QFAAG0) work's well when download the ibeacon.hex.
The target set as follow:
Based SDK 9.0 "ibeacon" example,nRF51822(QFABC0...
Anyone seen the new nRF52 online power profiler ?
It's an online tool that estimates the current consumed by your BLE application.
This allows you to better understand...
Hi,
Before starting advertising using advertising_start() function, if pstorage function is used to write data, then it gets stuck at that point as no pstorage handler...
Hello, I have an issue with ble_app_hrs_rscs_relay that doesn't seem to exist with the other sample projects.
The project compiles without any issues, but when I run it...
