I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hi All,
I am designing a circuit with nrf51822 and mcp25625 (microchip spi can interface). mcp25625 has an internal 16mHz xtal clock circuit and a digital clock out, I...
Hi, i'm kinda a newbie on this, and i'm trying to port the SDK available for arduino to a PIC, i followed the instructions on the SDK and also here
Now i want to verify...
I ran into an issue recently of attempting to make a pstorage_update call from the callback set in pstorage_register . It resulted in a difficult to track down error, so I...
I have a USB dongle of nRF24LU1p and it is identified as the Basic Remote firmware with a VID:PID of 1519:002B. I would like to reprogram it over USB but do not know how to...
For nRF 51822 radio transmission, the payload packet is started at the NRF_RADIO->PACKETPTR. Then what is the packet size? is there any parameters to control the packet size...
I should have an own function wich is called upon after Port 3 goes low. I haven't succeeded yet using ppi channels. (I'm using the NRF51422)
For the moment the code is...
Hello folks ;
I'm new here and glad to have such kind people around to see helping those other developers ..
Here is my question
I'm using one of the NRF24L01 modules...
Hi,
I'm using the attached circuit and we recently took our product to FCC testing and failed the 2nd harmonic because we were transmitting too much power.
I'd like...
Hi All,
We have been working on Arduino Mega board with BLE shield. We want to get the address of the BLE shield and we are using aci library for that.
I found this...
I'm in the process of designing a consumer product using the nRF51822. I'm using the "square wave" antenna and matching circuit exactly as the are in the development kits...
Hello,
we are based in Germany and need a way to mass-programme the nrf51822 for production with our custom firmware+the softdevice.
Unfortunately we haven't found any...
Hi
I am writing an application that will have to switch the radio in between a number of different modes. (With/without AutoAck, and with/without dpl).
I have been looking...
Hello,
according to the documenation, the function sd_ant_burst_handler_request() can return with the error code NRF_ANT_ERROR_MESSAGE_SIZE_EXCEEDS_LIMIT. When will the...
Hi,
I was thinking if it is possible to use, per example HackRF greatscottgadgets.com/.../ , to tune the antena of the nRF15822 seeing if it is transmiting on the 2.4Ghz...
