I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
s120 1.0.0.1-alpha loads fine
s120 1.0.0.2-alpha won't load - The given hex file did not load successfully
s120 1.0.0.3-alpha won't load - same error message
See attached...
Folks,
Prototyping a wearable device using the nRF51822, so we're talking about Bluetooth LE and the 2.4 GHz band (although the protocol probably doesn't matter). Since...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,we can send data from server to client by sd_ble_gatts_hvx() in ble_app_hrs
but:
1.How does the client receive those data?
2.How dose the client send data to server...
I'm totally new to Nordic, ARM development, and the mbed platform. Not new to embedded development however.
So far I can't get the simplest possible program to run.
...
I just received my nrf51822 dev kit and noticed that the SWD debugging cable will only connect to the PCA10004. The PCA10005 that came with my kit has pin 2 missing, rather...
HI,
I wrote my application based on "MasterEmulator->ProximityDemo" for testing device with nrf51822. My device have to switching between Gazell and BLE stacks so all the...
Hi
In ble uart project, the data is used string format. Now, we want to modify uart apps to tx/rx binary format. Could you tell us how to modify the uart apps? Thanks.
...
I added a local service with a characteristic with the Notify permission set.
On the device I'm connecting from to the nRF8001, I can see my custom characteristic has a 0x2902...
I'm designing what is essentially a small beacon board built around an nRF51822. On the antenna outputs I've used the discrete component balanced to unbalanced circuit shows...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
nrf24LE1 external interrupt is not easy to use , I use nRF24LE1 48pin chip, and the external interrupt 0 (GPINT0)is configured to falling edge trigger, but it can not be triggered...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
