Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Description:
I am experiencing a non-linear "sticking" and "jumping" behavior when attempting to monitor the VDDH rail using the internal VDDHDIV5 channel on the nRF52840...
I don't know where to make this suggestion, so hopefully my suggestion makes it to the right person.
I completed BLE Fundamentals and the nRF SDK courses.
I would have...
Hi! I'm migrating some code from an 14.2.0 SDK to the 17.1.0 SDK and cleaning up a big mess.
Whenever I call nrf_power_pofcon_set ( true , NRF_POWER_POFTHR_V27) with either...
I am trying to debug/flash an nRF54L15 using the nRF Connect VS code extension and a J-Link EDU. Although my J-Link EDU works fine with all the Segger tools, including Ozone...
Hi
I am looking to a wearable / health tracker which will be mounted on a persons head.
Are there any precertfied nRF7002 module where I don't need to go through the pain...
We tested several hundred connection and disconnection cycles with the nRF52840 BLE dongle. The first hundred cycles operated without any issues. However, at a later cycle...
Hello, I am trying to use twister + ztest to run some basic tests on my device custom project and nrf5340 Here are the contents. Current Directory Structure
Contents of...
Hello there,
I'm developing a project with NTN using a Vivo chip, a Brazil operator chip, but I'm having trouble with an nRF9151 and I'm trying to put it in NTN mode, but...
Hi
I took over a nordic project and was asked about the bluetooth version used in that project.
How Do I figure this out?
I am using a nrf52833. The firmware is developed...
Hi all
While connecting to a peripheral that has ble buttonless dfu characteristic i need to enable indicate.
Undortunately i get back err: 0x11(17) from sd_ble_gat...
I'm struggling with the nrf sdk v2.9.2 zigbee light_switch example. I copy the example, add this to proj.conf
CONFIG_ZIGBEE_CHANNEL=25 CONFIG_ZIGBEE_CHANNEL_SELECTION_MODE_SINGLE...
Hi.
I have a question.
When sending packets from a ZIGBEE product (with TI CC2538 built in) and receiving them with an nRF52840 Dongle (Sniffer FW) and Wireshark, is it...
Hello Everyone, I was wondering if there is any easy "ready configuration" way to directly set BLE advertising and connection interval with adding some config to the prj.conf...
Hello! Using NCS 3.2.1 I am implementing DFU over SPI (the NRF54L15 is SPI slave) using the "DFU Target" library. It works very well, as long as I am connected with JLink...
