I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
Hello,
we have been testing channel sounding with single antenna configuration, however we are not sure of which accuracy to expect. Also, we are not sure of the reliability...
Hello Nordic team,
I have a question regarding the Bluetooth LE RF-PHY Intermodulation Characteristics test (Bluetooth Core Specification Vol. 6, Part A, Section 4.4)...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
Recently the VSCode extension has seemed to become extremely slow / unresponsive when triggering a build
Judging by the vscode popup on every build telling me there's an...
Hi
in Exercise 5 – FOTA over Bluetooth LE I get the following warnings. Can you comment and fix?
I am on v3.4.1:
1. warning: Deprecated symbol BOOT_ECDSA_CC310 is enabled...
Hi,
I just read the nrf54l15 errata [100] of the nrf54l15. It's actually a huge issue, as we do have an interrupt line on one of the affected pins, that is active low, eg...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
Hi,
Our project has chosen nPM1300 as the PMIC, and our project's battery is only 28 mAh. When we tested the battery configuration file using the nPM PowerUP app, we found...
Hi,
I am testing on the nRF5340dk using NCS v3.4.0. I took the official Zephyr Extended Advertising advertiser sample (samples/bluetooth/extended_adv/advertiser) and added...
I have an application that will be greatly simplified if I can power the nRF52832 via the clamp diodes on the GPIOs. I have multiple GPIOs pulled up to around 3.3V with some...
I am developing a custom nRF54L15 board using a GigaDevice GD5F1GQ5REYIGR SPI NAND connected through the nRF54L15 sQSPI/MSPI interface.
I have encountered a highly reproducible...
I have dev kit nRf54LM20 - DK with specs: PCA10184 0.7.0 2026.12 1051821506 I am using 3.3.0 SDK. When I run peripheral sample project from NCS 3.3.0 it works completely fine...
Hi,
We are using the nRF5340 and a Pixel phone for the nRF OTA update. We observed that the Pixel phone application disconnects after updating the connection parameters...
