I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi
1、Now we connect the VDD to the battery voltage (3.4-4.2), and the VDD_GPIO is fixed at 3.3V. In order to match the GPIO of other peripheral cpus, will all GPIO be connected...
We plan to use the 52840 to make a module with an external flash, if we apply the QSPI peripheral, must we use the P0.23,P1.00,P0.21,P0.25,P0.19 pins recommended in the specification...
I want to run my software on nRF52832. It is already running on nRF52840.
What are the changes I would require making this transition.
We are using soft devices and all...
Hi.
Please help project evaluation.
The project is a BLE HID mouse , it need playback LC3 audio sound sometime.
Can we use HID function and LC3 function at the same...
Hi,
I am unable to connect and program a custom board with nRF52833 after performing 'Erase All' using Segger IDE (V5.66).
Those boards were programmed a few months ago...
Hello! I am a total newb but trying to self-learn embedded programming / electronics. I recently received a nRF52840 development kit and followed instructions at https://nordicsemi...
Development environment :
ARM-GCC version - "gcc-arm-none-eabi-6-2017-q2-update"
nRF SDK version - nRF5_SDK_15.2.0_9412b96
nRF Mesh SDK version - nrf5SDKforMeshv310src...
Burn the firmware of nrf/samples/bluetooh/multi-adv-set, the mobile phone scans the broadcast of 2 mac addresses.
How to set multiple broadcasts of nRF5340 to the same mac...
I'm trying to use BLE and radio synchronization with a nRF5340. For this I need to integrate radio synchronization and HCI RPmsg into the nRF5340 NET core. My synchronization...
Nice to meet you
What is the recommended land size for your product nRF52840-CKAA?
Mechanical information was found at the following URL.
" ">infocenter.nordicsemi.com/index...
I am trying to get the UARTE0 on the nRF9160 DK to transmit some bytes through the Virtual COM port. I am not sure why it does not work. I have included my source code below...
I followed the directions/videos to install the nRF development environment for VSCode on a Windows machine: https://www.youtube.com/playlist?list=PLx_tBuQ_KSqEt7NK-H7Lu78lT2OijwIMl...
I'm new to nRF have done the "nRF Connect SDK Fundamentals", course and have create a custom characteristic to read and write but I cannot get notification to work.
I'm...
Hello everyone,
I am still being not able of getting my nRF9160 DK connected to the nRF Cloud. I have already done what this link https://api.nrfcloud.com/v1/#section/Error...
