I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
To whom it may concern,
Good day, I need your help to activate my sim card on my Nordic Thingy:9. Sim card was provided by Beeline Kazakhstan local provider. Local provider...
Does anyone have a port of nRF5 SDK ble_app_uart_c to the nRF52840-dongle? The goal is to replace the UART with a USB CDC transport.
Thanks in advance.
Cheers,
Je...
hello Nordic
i work with nrf52840, with zephyr (2.6.9)
i have 4 leds on my board that i want to control seperatly with pwm
i put each one of them on a different pwm...
Based on this weblink I need at least 4MBytes of flash for doing a full cellular update on the nRF9160:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples...
There is a custom bootloader in the flash having a address of 0x27000 immediately after the soft device occur, the bootloader code jumps directly to our beacon application...
Hi,
I am using a Mac (Apple silicon) to develop a Matter device. We are using one of the Matter examples, but when importing the example we get the error that GN Tool cannot...
Hi,
When I download my code, I get the error hardfault, but when I reset it, the program runs. I'm not sure why it's giving me this error; could you please tell me how to...
Step Three of "Programming the nRF Sniffer firmware" states:
3. Locate the firmware HEX file for your DK or dongle.
All firmware HEX files are located in Sniffer_Software...
Hi,
I want to know what parameters（<NW-provided_eDRX_value） mean.
The following figure shows parameters
A:Requested_eDRX_value
B:<NW-provided_eDRX_value
C:Paging_time_window...
Hi,
dk: PCA10090 0.9.0 2019.21
ncs: v1.9.0
example: serial_lte_modem
How to send HEX data to the server with the command #XTCPSEND at ncs v1.9.0 the old sdk ncs v1...
Hi,
1. Please provide the COMP input voltage precision in CROSS event on VIN+ and VIN- crossing mode
2. When the input voltage changes to the minimum, the output terminal...
Hi everyone,
i would like to ask if there is available an example project for the nRF9160DK that uses aws_iot through a NBIOT modem configuration.
I took the aws_iot sample...
Hi,
I am trying to connect my LSM9DS1 with nrf52840, this is Arduino nano 33 BLE board. I already figured out that i had to enable it and enable TWI bus. After some readings...
I am trying to change the curvetype of the ecdh example from NIST secp256r1 to Curve25519 or Koblitz secp256k1.
To achieve this I enabeled Koblitz curve secp256k1 and Curve25519...
Hello Devzone,
Our research group is using the NRF52832 chip embedded in a flexible substrate to transmit EMG (muscle) signals via Bluetooth. We’ve been having a couple...
