Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
We have a custom software for our custom board. And would like to investigate a little in the AT commands going to the modem and the responses
is there a config...
I am using Connect SDK v1.7.1 and Ozone v3.26b. When I click "Debug with Ozone" in VS Code, I receive the following warning in the Ozone console:
I am able to correct...
Hello,
While developing the device, I found that the SAADC module on the NRF52833 incorrectly measures the voltage on the NRF_SAADC_INPUT_VDD channel if you set the REGOUT0...
Hi,
We have a device in production based on nrf52840 which uses UARTE to TX/RX data to/from a washing machine and in paralel communicates with a Phone App via BLE.
SD...
Hi,
I am using nRF5340 Audio DK. I have 3 kits currently and I have programmed one as a headset and the other two as gateways.
I would like to use the whitelist so that...
I think it'd be nice if there was a connect button like this.
but my device appear one button.
I think the multi-link function should be possible to solve this problem...
Is there a working example with using gpio_dt_spec for accessing gpios?
I used the code provided from https://docs.zephyrproject.org/latest/reference/peripherals/gpio.html#c...
Hello, by usingnrf52832 DK and testing some examples i found out that the example peripheral UART was not going like I wanted to do. He is going to sleep mode after 3 minutes...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v1.0.1%2Fmd_doc_getting_started_how_to_models.html
Linkte verilen yönergeleri takip ederek...
Hi all, I discovered that if I get BLE_GAP_SEC_STATUS_AUTH_REQ while pairing, the device is basically useless until a new reset. I would be extremely grateful for some help...
Hi All,
I have a project which uses the zephyr shell, but I can reproduce the issue with zephyr/samples/subsys/shell/shell_module or any other sample making use of the UART...
uint32_t address = XIP_ADDRESS + addr ;
uint8_t * p_data = ( uint8_t * ) address ;
for ( int i = 0 ; i < len ; i ++ )
{
data [ i ] = p_data [ i ] ;
} The Pin of QSPI...
Hello,
I recently installed the VSCode Extension for nRF Connect and I am experiencing, what seems to me, strange behaviour.
Here's the steps:
I create a project from...
