I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
1. I had done the pairing without any authentication but now I want to do it with the authentication with an authentication key.
2. please provide some sample code regarding...
Hello DevZoners, I hope you are all doing great!
I'm struggling to understand how this works.
I've been following the NCS Tutorial part 2 to implement the PWM peripheral...
Hi,
I am working on nrf5340. I would like to change the TX and RX default pin of uart0 to <33> and <32>, I modified the file "nrf5340_cpuapp_common.dts" as below.
The...
I've been develop the other MCU;s DFU driver for the nrf52832 recently, and I ran into several problems.
The first I show you my DFU step in the RTL8720( Be the central...
Hi there!
I'm using the nRF Connect SDK with the VScode extension for developing an application for the nRF9160DK. I've taken the lwm2m_client sample as base and rewrote...
I'm struggling to get buttonless DFU to work with FreeRTOS. I've gotten buttonless DFU sample to run on the hardware. I also have FreeRTOS running on the hardware. However...
Hi team,
Environment :
nrf52840
s140
1.How to enable the second regulator stage REG1 use of DC-DC converter ?
2.What is the default configuration HFCLK and how to...
Hi Everyone,
Wanted to test the NFC library provided by the nrfxlib on the nrf5340DK. Added the following config file:
Resulted in:
How could I check the reason...
Hi,
I have added a nrf-9160 DK device to nrf cloud and it is always is shown as disconnected (disconnect reason MQTT_KEEP_ALINE_TIMEOUT ).
Previously i have updated the...
Hi
We are using a nrf52840 on a custom board.
The board always worked fine.
Flashing is done with :
- SEGGER J-Link EFM32GG-STK3700
- nrfjprog version: 10.15.0...
I am seeing the error below when I try to launch a debug session inside the IAR IDE.
I am working on the nRF52840DK and am seeing this error on the DFU example in the...
I'm Using sim card which support both LTE and NB-IoT. In some areas i can't use LTE-M and in that case i need to switch it to NB-IoT. I referred and there is fallback method...
I am using the Ceedling framework for unit testing my firmware. This has qorked quite well. But now I wanted to use the section variables to decouple my code a bit more. And...
Hi. I would like to know how to do a DFU over UART using a custom desktop application (without using nrfutil command nor nRF Connect app). What would be the UART protocol...
Hello,
I have the same problem as this topic: https://devzone.nordicsemi.com/f/nordic-q-a/77267/nrf9160-azure-iot-hub-on-thingy91-mqtt-connect-error
I'm using nrf Connect...
