Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
I want to understand the ROM layout and set the memory map.
Please tell me how to know the layout of the current ROM. (Mainly the range used by MBR area and FDS area)
...
Hi!
I use ncs v1.3.0 and mfw 1.2.0 on a nRF9160 DK v0.8.5.
My app runs in PSM mode alternating between LTE and GPS following Jan-Tores suggestions in his response to my...
LTE Link Monitor doesn't seem to be able to detect any serial interfaces on macOS that are not the DKs (or don't have 3 serial ports)
See this hacky implementation: https...
Hi,
I am using NRF24L01 with arduino using RF24 library ( https://github.com/maniacbug/RF24 ).
While executing the transmission code i have observed the following line...
Hello dear!
This is my first post righ here. Hope you can clear my doubt.
I'd like to know if the CTE and IQ sampling features are accessible using the BLE MESH?
I'll...
Hello,
I have a device which sends a provisioning request to two other devices in a Thread network. They both receive the request and both send a provisioning response,...
Hello. I am testing the Secure DFU for NRF51 with softdevice S130 provided in the SDK Version 12. 3.0 following the steps in this guide. https://devzone.nordicsemi.com/nordic...
Hello!
I have a custom board with nRF52810 and s132. BLE connection is secured with passcode. it works.
I would like to get exact passcode entered by User if the passcode...
Hi support team.
My project build using keil IDE working stable. But when I change to build using makefile, although build success with hex file output and and everything...
Hi Team,
I have gone through many threads on the forum but still in doubt regarding how to interface nrf52 over HCI to the Linux based host.
My understanding is currently...
When building example ble_app_interactive_s132_pca10040, SES asks for missing "nfc_t2t_lib.c" and "nfc_t2t_lib_al.c" files. This happens when SES is 'Preparing target for...
Hi,
I'm currently trying to use 2 channel SAADC to measure 2 analog input port
I've searched other questions in this forum and referred SDK example
Actually, I could...
Hi All,
I want to measure the battery level in my nRF52840 design using the ADC.
I came across this thread in the nordic devZone https://devzone.nordicsemi.com/nordic...
Hey all, I am bit late to the party but I was following Vidar's HX711 Library and was able to configure it to work after a long period of time (Pardon me, I am new to this...
